Jump to content
SAU Community

Rate Your Tune.

Bullet32

By Bullet32,
in Australian Capital Territory

 Share

Recommended Posts

Scooby Veteran

Scooby

Posted
Posted (edited)

Autotech now has Nistune stock ecu chip burning software, behaves exactly like a PFC except a programmable chip gets soldered into the ecu in place of the original before tuning. Unfortunately not fully for R33GTSt - -some restrictions - but just about everything else Nissan with an ecu.

Edited by Scooby
Bluprint Veteran

Bluprint

Posted
Posted
Autotech now has Nistune stock ecu chip burning software, behaves exactly like a PFC except a programmable chip gets soldered into the ecu in place of the original before tuning. Unfortunately not for R33GTSt but just about everything else Nissan with an ecu.

RE HEH HEH HEH HEH HEH HEEEEEEEALLLLLYYYYY???????

Scooby Veteran

Scooby

Posted
Posted (edited)

My constant hints to Pete came to fruition, he confirmed today that they have a dealer license. Current price is $220AUD for board, $200AUD NIStune Software (Individual Users License) and documentation set. Additionally, shipping and transaction fees may apply.

Then its just the cost of the tune.

Looks like RB25 is supported but not with VCT. Check out the Nistune site, pretty much explains eveything. http://home.aanet.com.au/nistune/

Cheers

Edited by Scooby
Bullet32 Veteran

Bullet32

Posted
  • Author
Posted

Well, my tune was done yesterday and I am very happy... Even though I didnt get much more power from it as we have reached the limits of the turbo and AFM, the boost response, mid range torque, fuel consumption and overall driveability have improved.

This tune was more about getting the engine to run spot on so that I wouldnt have any drama's with pinging while on the track.

9 / 10 for John and Angelo at Trojan - Power FC RB25DET Dyno tune, great tune, right price and anything small and incidental that needed doing (such as rubber grommets / hoses) was done at no extra charge... Very happy.

Pic attached: - Check out that awesome power curve!! :thumbsup:

post-17958-1203645354_thumb.jpg

widebody32 Community Regular

widebody32

Posted
Posted
Fair enough, but I think you'll find that it makes at the very least 1,350hp at the wheels, with still more to go.

Anyway's you should bring the beast to the dyno day I'm sure we would all be interested in seeing and hearing how she goes.

I know this car very well as my friend had a hand in it. It makes 1350 at the flywheel and revs to almost 13000 revs. It does make good power but will not make much more as they are already on the biggest turbo setup and as you can see by the revs massive cams.

Would love to come to the dyno day but unfortunately due to a well known machinist have had to pull it back down again due to valve float issues.

Will be at the next one as have changed machinist's and instead of work taking 8mths it is now almost all completed.

As for the torque mine makes 650lb at 2psi and peaks at 2266lb at 28psi in fourth gear pulls or in nm it makes over 10000nm it makes 2psi by 2800 and full boost by about 5000

As for tunes i would be takin it directly to Jake as i was speakin to him recently and he does alot of tunes on skylines and said he does all the tuning on his dyno.

May save some money

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      I myself AM TOTALLY UNPREPARED TO BELIEVE that the load is higher on the track than on the dyno. If it is not happening on the dyno, I cannot see it happening on the track. The difference you are seeing is because it is hot on the track, and I am pretty sure your tuner is not belting the crap out of it on teh dyno when it starts to get hot. The only way that being hot on the track can lead to real ping, that I can think of, is if you are getting more oil (from mist in the inlet tract, or going up past the oil control rings) reducing the effective octane rating of the fuel and causing ping that way. Yeah, nah. Look at this graph which I will helpfully show you zoomed back in. As an engineer, I look at the difference in viscocity at (in your case, 125°C) and say "they're all the same number". Even though those lines are not completely collapsed down onto each other, the oil grades you are talking about (40, 50 and 60) are teh top three lines (150, 220 and 320) and as far as I am concerned, there is not enough difference between them at that temperature to be meaningful. The viscosity of 60 at 125°C is teh same as 40 at 100°C. You should not operate it under high load at high temperature. That is purely because the only way they can achieve their emissions numbers is with thin-arse oil in it, so they have to tell you to put thin oil in it for the street. They know that no-one can drive the car & engine hard enough on the street to reach the operating regime that demands the actual correct oil that the engine needs on the track. And so they tell you to put that oil in for the track. Find a way to get more air into it, or, more likely, out of it. Or add a water spray for when it's hot. Or something.   As to the leak --- a small leak that cannot cause near catastrophic volume loss in a few seconds cannot cause a low pressure condition in the engine. If the leak is large enough to drop oil pressure, then you will only get one or two shots at it before the sump is drained.
    • GTSBoy
      Help! Leak coming under transmission

      By GTSBoy · Posted

      So..... it's going to be a heater hose or other coolant hose at the rear of the head/plenum. Or it's going to be one of the welch plugs on the back of the motor, which is a motor out thing to fix.
    • MBS206
      Mistakes were made, my R34 Story

      By MBS206 · Posted

      The oil pressure sensor for logging, does it happen to be the one that was slowly breaking out of the oil block? If it is,I would be ignoring your logs. You had a leak at the sensor which would mean it can't read accurately. It's a small hole at the sensor, and you had a small hole just before it, meaning you could have lost significant pressure reading.   As for brakes, if it's just fluid getting old, you won't necessarily end up with air sitting in the line. Bleed a shit tonne of fluid through so you effectively replace it and go again. Oh and, pay close attention to the pressure gauge while on track!
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      I don't know it is due to that. It could just be due to load on track being more than a dyno. But it would be nice to rule it out. We're talking a fraction of a second of pulling ~1 degree of timing. So it's not a lot, but I'd rather it be 0... Thicker oil isn't really a "bandaid" if it's oil that is going to run at 125C, is it? It will be thicker at 100 and thus at 125, where the 40 weight may not be as thick as one may like for that use. I already have a big pump that has been ported. They (They in this instance being the guy that built my heads) port them so they flow more at lower RPM but have a bypass spring that I believe is ~70psi. I have seen 70psi of oil pressure up top in the past, before I knew I had this leak. I have a 25 row oil cooler that takes up all the space in the driver side guard. It is interesting that GM themselves recommend 0-30 oil for their Vette applications. Unless you take it to the track where the official word is to put 20-50w oil in there, then take that back out after your track day is done and return to 0-30.
    • PranK
      My new to me M35 Stagea wagon

      By PranK · Posted

      Nice, looks great. Nice work getting the factory parts also. Never know when you'll need them.
×
×
  • Create New...