Jump to content
SAU Community

Wtb: R33 Diff

toffaz

By toffaz,
in Tasmania

 Share

Recommended Posts

DJRIFT Veteran

DJRIFT

Posted
Posted

all turbo skylines come out with a viscus lsd. these can be reshimed to act like a normal viscus. lock under acceleration or shimed super tight to be like a welded/ 2 way diff. a new shim from nissan costs around $10 and for someone thats done one takes only a few hours.

KAZZA do cheap locker diffs. 1 1.5 and 2 way for about $1100 which is cheap for a new diff centre.

so are you after a complete diff or just a centre. if yours is just single spinning than a re shim and some new lsd oil and it would probably be sweet as.

Link to comment
https://www.sau.com.au/forums/topic/206405-wtb-r33-diff/#findComment-3652708
Share on other sites
ardie Experienced

ardie

Posted
Posted

Hey mate I got a weldy that has never been used, never even put it back together, the centre is still out of housing so you can have a look at it if you want, it comes with everything including, all you need to do is bolt it back together and away you go.

I welded it up at my old engineering job back in Melbourne and then decided to sell the car, give me a PM if you are interested in it mate

Oh and I also have a HICAS lock bar if you are intereted

Link to comment
https://www.sau.com.au/forums/topic/206405-wtb-r33-diff/#findComment-3653656
Share on other sites
toffaz Contributor

toffaz

Posted
  • Author
Posted
so are you after a complete diff or just a centre. if yours is just single spinning than a re shim and some new lsd oil and it would probably be sweet as.

haha already had two 1.5mm shims in it :) kinda went bang on the way to devonport n had to get trailered home haha

Hey mate I got a weldy that has never been used, never even put it back together, the centre is still out of housing so you can have a look at it if you want, it comes with everything including, all you need to do is bolt it back together and away you go.

I welded it up at my old engineering job back in Melbourne and then decided to sell the car, give me a PM if you are interested in it mate

Oh and I also have a HICAS lock bar if you are intereted

Already got a HICAS lock bar but thanks anyway ;) how much u looking at for the diff?

Link to comment
https://www.sau.com.au/forums/topic/206405-wtb-r33-diff/#findComment-3654984
Share on other sites
  • 3 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      NC MX5

      By MBS206 · Posted

      This sounds like someone who would have owned an R33 in their past... It's okay, I'm 100% picking up what you're putting down Mark.
    • MBS206
      Jacks that fit under GTR lips that can reach the subframe?

      By MBS206 · Posted

      Just back on what was raised about jacking off the the tow/tie down point on the front of cars. I've used it plenty. I've also watched it on a car where you could see it move the front end of the car. It was like the front end/whole car being tweaked and twisted a bit. I will say, I struggle to find good jacking points on MOST cars. The ones that have good points, I then normally struggle to find a jack tall enough to make the car change height!   One of my go to points for either the jack, or the axel stands though, is either a suspension pickup point, OR a subframe to chassis major bolting point. I actually think its the subframe on my R33 that has a bit of a bend in it, from being jacked in the middle too. However, it could have been one of my many other cars I've had over the years! Or it could also be the from me jacking it up, and the fact the top of the front radiator support isn't there, so it can allow the front of the car to move and bend etc.
    • GTSBoy
      M35 Aftermarket Fuel Pump

      By GTSBoy · Posted

      My apologies. I forgot we were talking about weird beard M series stuff. Had been talking elsewhere with someone about an R33 with similar subject and got confused.
    • The Bogan
      NC MX5

      By The Bogan · Posted

      Nope, I don't like the look of ND RF, or any ND really, I don't like their faces or arses, why, because of their "modern" lines, the NC, whilst "modernish" has a more rounded shape that I like Well, that's how my overly judgemental eyes see it anyway  
    • Dose Pipe Sutututu
      M35 Aftermarket Fuel Pump

      By Dose Pipe Sutututu · Posted

      Should be more than fine, especially the overall fuel pressure would never exceed 3.5bar (assuming that thing never gets more than 0.5bar of boost in stock form). According to the chart, it's 11amps.
×
×
  • Create New...