Jump to content
SAU Community

Please Help: I Need To Borrow An Rb25 Afm


Recommended Posts

Hey guys, I am in desperate need of an rb25 afm off a series2, all I need it for is to test my engine and see if the reason it isnt starting is becuase of the afm as my one is pretty old and had been sitting around in a dusty old shed for ages. I cleaned it using carby cleaner and it still didnt work so if anybody could loan me theirs it would be greatly appreciated.

It will literally take 5 mins, I dont even need to tighten up the clamps or andything, all ill do is wire it up and turn the key.

If you could help that would be awesome, as I need to get the car going for the sale

Cheers

Ryan

Hey guys, I am in desperate need of an rb25 afm off a series2, all I need it for is to test my engine and see if the reason it isnt starting is becuase of the afm as my one is pretty old and had been sitting around in a dusty old shed for ages. I cleaned it using carby cleaner and it still didnt work so if anybody could loan me theirs it would be greatly appreciated.

It will literally take 5 mins, I dont even need to tighten up the clamps or andything, all ill do is wire it up and turn the key.

If you could help that would be awesome, as I need to get the car going for the sale

Cheers

Ryan

I have one off a S1.5/2 (pink stickered) in working order, i was actually getting ready to sell it but havent got round to it yet, you are welcome to borrow it as long as it comes back in good working order the way it leaves me, I think i actually have to head to L'ton late next week, not 100% sure yet, but anyway its here in D'port,Damo

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Nah. You need 2x taps for anything that you cannot pass the tap all the way through. And even then, there's a point in response to the above which I will come back to. The 2x taps are 1x tapered for starting, and 1x plug tap for working to the bottom of blind holes. That block's port is effectively a blind hole from the perspective of the tap. The tapered tap/tapered thread response. You don't ever leave a female hole tapered. They are supposed to be parallel, hence the wide section of a tapered tap being parallel, the existince of plug taps, etc. The male is tapered so that it will eventually get too fat for the female thread, and yes, there is some risk if the tapped length of the female hole doesn't offer enough threads, that it will not lock up very nicely. But you can always buzz off the extra length on the male thread, and the tape is very good at adding bulk to the joint.
    • Nice....looking forward to that update
    • Neg, the top one is actually for the front. The sizes are 18x10.5 +18 and 18x11 +32.   I measured many times but I'm sure I'll have problems as this is the thread for problems.
    • Just one thing; tapping tapered threads is tricky. Taps are always tapered and you would generally run it as far as you can, but with a tapered thread you have to stop much sooner otherwise the wide part of the taper will run in too far and you will have to thread the sensor in too far too as well (possible that it will never make a good seal) BTW nice wide wheels, I guess the top one is for the back!
    • Welp, good to know. Will have to wait awhile until steady hands with drills and taps are available. In other news, these just arrived! I will weigh them for posterity. Edit: 11kg each (or 10.9/11.1 depending on what my scale decides over multiple tests, the 18x11 don't seem to weigh noticeably any more than 10.5)  
×
×
  • Create New...