Jump to content
SAU Community

Recommended Posts

$600 is way too much

Get them and take them into a local panel shop, be realy nice to the guys in there and just say to one of the guys working that you will give him personally (not the shop, but the worker) $300 if he paints your covers in JWO after hours and there's no rush on the job

$600 is way too much

Get them and take them into a local panel shop, be realy nice to the guys in there and just say to one of the guys working that you will give him personally (not the shop, but the worker) $300 if he paints your covers in JWO after hours and there's no rush on the job

I agree, $600 is way too much and N1GTR has the right idea about approaching a painter in your local panel shop. For $600 you're probably still getting used covers that are just repainted. In korea I can get my RB26 covers painted at a panel shop for ~$250 USD so I'm sure you can get it for about the same in Aus. It's expensive in japan to buy newly painted covers.

Prices for Nissan OEM Painted brand new covers from Japan...

Black

Rocker cover EX side $219 USD

Rocker cover IN side $219 USD

Rocker Ornament cover $263 USD

Front cam pulley cover $315 USD

Red

Rocker cover EX side $210 USD

Rocker cover IN side $210 USD

Rocker ornament cover $242 USD

Front cam pulley cover $125 USD

Gold

Rocker cover EX side $305 USD

Rocker cover IN side $305 USD

Rocker ornament cover ???

Front cam pulley cover $181 USD

I would expect JWO to be more expensive... just to give you an idea.

Edited by chak8080

Go and see Mick at Micolour, He has done plenty.

And well priced too.

I THINK its around $110ish a piece to paint maybe a touch more, you would have to check with mick.

And he is able to remove them off the car and reinstall if required,

although taking in just the pieces is easyer

Edited by vsute
Go and see Mick at Micolour, He has done plenty.

And well priced too.

I THINK its around $110ish a piece to paint maybe a touch more, you would have to check with mick.

And he is able to remove them off the car and reinstall if required,

although taking in just the pieces is easyer

yeah sounds good

ill give them a call tomorrow

or i might even visit them to see what they can do about my scratch on the side of my car too! :D

Go and see Mick at Micolour, He has done plenty.

And well priced too.

I THINK its around $110ish a piece to paint maybe a touch more, you would have to check with mick.

And he is able to remove them off the car and reinstall if required,

although taking in just the pieces is easyer

ouch $550 for the cover set

not much choice really if mil jade is required.

yep i mentioned that before

depends on what your doing with the car i guess :rofl:

just when i think of it , its normally about $800 for a 4 piece body kit to get painted .. engine covers are so so so much smaller lol

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • @666DAN sorry to bring you and old thread.     I've got my de+t done and it's all running great other than 1 small issue.    Car has remained auto with the na auto and tcm, I've used a stagea ecu with. NIstune board and everything is great other than my gear selection on the dash. It illuminates park, reverse, neutral, 3rd and 2nd when selected . But nothing when in  drive or what gear your in when you pop it into tiptronic. I'm sure there is maybe 1 wire in the ecu plug I need to move to rectify this. Do ya have any ideas?     Cheers man
    • Well I recently changed my rear axles and was thinking if I bumped anything, I have been driving the car for a while now though... But it has been raining today so everything is wet under the wheel arches. Brakes feel fine and can't hear any of the metal screamers, I had a squeak coming from one of the handbrake drums but that seems to have gone away a while ago. I was going down a hill when it lit up and I did feel the abs bite for a second and question why it did it?
    • Correct. Um. I dunno. I haven't cared enough about the way that the NA cars work to know for sure. But..... The 33/34 turbo manual cars have an electronic speed sensor in the gearbox that outputs a +/- (ie, sawtooth AC) voltage signal. That is connected to the speedo. The speedo then outputs a 0-5v square wave (ie, PWM) signal that the ECU (and any other CU on the bus) sees. The speed sensor is NOT directly connected to the ECU. So here's the problem. Your new ECU expects to see the PWM signal, but must somehow be getting a direct signal from the diff speed sensor. Which would suggest that the wiring of the NA car is not the same as the turbo cars. I think you will need to spend some time with (hopefully the wiring diagram for the car) and a multimeter to see what is connected to what. Then, presuming I am correct**, you would then want to separate the ECU speed signal input from the rest of the car's wiring, and probably either buy a speed signal converter, or build one using an arduino (or similar). That would take in the speed sensor signal and output a scaled (and suitably rearranged) signal for the ECU. ** We shouldn't presume that I am correct here, because there might be something else crazy going on. I don't think you could convert the speedo to be fed from the gearbox sensor, because the pulse rate from that sensor is probably different to the diff sensor and then the speedo would read wrongly. And this also wouldn't fix the ECU's problem either, because the ECU doesn't want to see the gearbox signal direct either (assuming that they are all on the same wiring, for some odd NA related reason, see above caveat!) Does this help? Probably not. Can you make it work? Almost certainly. With the above work. You should buy a handheld oscilloscope from Aliexpress so that you can view these signals directly. Connect up the probes and drive the car. Show photos of the screen when drving at known speeds and connected to different places, and we'll see what we can learn about it.
    • Assuming your brake pads are not worn right down, I'd add a little brake fluid. Is there any sign of a brake fluid leak?
    • Hello all,  I need of some help. On my drive home my handbrake light lit up and started flashing. When I got home I checked my handbrake sensor under the centre console and nothing seemed out of the ordinary. I have scanned my car via the consult port, no codes shown. Checked my brake fluid as well which is half full. Tried unplugging the brake master but it didn't change anything. Thoughts on what it could be? The master float doesn't seem to be stuck. My car is an 1998 ER34 sedan GT. No hicas but has ABS Photos below 👇🏾 
×
×
  • Create New...