Jump to content
SAU Community

........

twin_spinner

By twin_spinner,
in General Automotive Discussion

 Share

Recommended Posts

mad082 Grand Master

mad082

Posted
Posted

a 3076 will bolt up to a standard manifold, but you may need some oil fittings.

as for the ecu, any aftermarket ecu will do the trick. you are best of asking the person who is going to tune it what they prefer. by using what they know the best you will get the best tune from them. if u get something they aren't familiar with you won't get as good of a result.

and i think a 3076 might be a bit big for a rb20 unless you are chasing big power. it will partly depend on what housing size you get.

but i don't know that much about what turbo is suitable for rb20's.

Link to comment
https://www.sau.com.au/forums/topic/207228--/#findComment-3666401
Share on other sites
Bunta Grand Master

Bunta

Posted
Posted

It does fit on the standard manifold...but by about 2mm you are best off getting a spacer made up to give the compressor a bit more clearence, apart from that you may need new oil and water lines and the intake will need to be jigged slightly

Link to comment
https://www.sau.com.au/forums/topic/207228--/#findComment-3666414
Share on other sites
mad082 Grand Master

mad082

Posted
Posted
It does fit on the standard manifold...but by about 2mm you are best off getting a spacer made up to give the compressor a bit more clearence, apart from that you may need new oil and water lines and the intake will need to be jigged slightly

actually the spacer you need is about an inch thick. i installed a 3076 on a mates 33. and you will need a new intake pipe as the compressor housing needs a 4" intake , and you need to make a few mods to the 'hot' cooler pipe.

a good bolt up replacement is a highflowed r33 turbo from gcg. they are a 100% factory fit, but as your turbo isn't standard some of the oil and water lines may have been altered, but a trip to a local hose place should sort you out.

Link to comment
https://www.sau.com.au/forums/topic/207228--/#findComment-3666438
Share on other sites
Bunta Grand Master

Bunta

Posted
Posted

ya an inch thick is what mine was too! i was saying it did 'fit' straight on to my manifold by 2mm but it was deemed more clearence would be wise ha ha

Im gonna be unoriginal and say that a GTRS or garret equivalent would be good on a RB20, cause the 3076 on my car felt a little laggy and that was with a 25

Link to comment
https://www.sau.com.au/forums/topic/207228--/#findComment-3666608
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Latest Posts

    • The Bogan
      NC MX5

      By The Bogan · Posted

      Yeah, it's getting like that, my daughter is coming over on Thursday to help me remove the bonnet so I can install the Carbuilders underbonnet stuff,  I might get her to give me a hand and remove the hardtop, maybe, because on really hot days the detachable hardtop helps the aircon keep the interior cool, the heat just punches straight through to rag top I also don't have enough hair for the "wind in the hair" experience, so there is that....LOL
    • joshuaho96
      Cas issue

      By joshuaho96 · Posted

      Could be falling edge/rising edge is set wrong. Are you getting sync errors?
    • joshuaho96
      Jacks that fit under GTR lips that can reach the subframe?

      By joshuaho96 · Posted

      On BMWs what I do because I'm more confident that I can't instantly crush the pinch welds and do thousands of USD in chassis damage is use a set of rubber jacking pads designed to protect the chassis/plastic adapter and raise a corner of the car, place the aforementioned 2x12 inch wooden planks under a tire, drop the car, then this normally gives me enough clearance to get to the front central jack point. If you don't need it to be a ramp it only needs to be 1-1.5 feet long. On my R33 I do not trust the pinch welds to tolerate any of this so I drive up on the ramps. Before then when I had to get a new floor jack that no longer cleared the front lip I removed it to get enough clearance to put the jack under it. Once you're on the ramps once you simply never let the car down to the ground. It lives on the ramps or on jack stands.
    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      Nah. You need 2x taps for anything that you cannot pass the tap all the way through. And even then, there's a point in response to the above which I will come back to. The 2x taps are 1x tapered for starting, and 1x plug tap for working to the bottom of blind holes. That block's port is effectively a blind hole from the perspective of the tap. The tapered tap/tapered thread response. You don't ever leave a female hole tapered. They are supposed to be parallel, hence the wide section of a tapered tap being parallel, the existince of plug taps, etc. The male is tapered so that it will eventually get too fat for the female thread, and yes, there is some risk if the tapped length of the female hole doesn't offer enough threads, that it will not lock up very nicely. But you can always buzz off the extra length on the male thread, and the tape is very good at adding bulk to the joint.
    • Duncan
      Mistakes were made, my R34 Story

      By Duncan · Posted

      Nice....looking forward to that update
×
×
  • Create New...