Jump to content
SAU Community

Spark Plug Replacement Procedure

mark_sudakov

By mark_sudakov,
in General Maintenance

 Share

Recommended Posts

mark_sudakov Community Regular

mark_sudakov

Posted
Posted

Is there any guide to getting to the spark plugs on an rb20? Ive found the Rb25 Tutorial, would that be similar or more things to take off. I had a look at the engine bay, and the only way i can figure out to get to the spark plugs is to take the crossover pipe and all the hoses that are associated with it, so that it can be removed. Then the plate and so on

Link to comment
Share on other sites
Fixxxer Community Regular

Fixxxer

Posted
Posted

You'll also have to remove the ignitor (black box) at the back of the engine to get to the last set of hex screws to get the valley cover off. I wish they made it easier. Also, don't be tempted to unplug the connection from the wiring loom to the coil, I broke two of the plastic clip connectors due to old age/heat.... bugger... I think the only way to replace these is to buy a whole new ignition wiring loom :D They still sit in ok but I secured them with some electrical tape just incase.

Fixxxer

Link to comment
Share on other sites
H@ME Mentor

H@ME

Posted
Posted

yeah it is the same as the rb25 guide, when i use to have my DE engine it was easy as but the det engine there is alot of stuff u need ot take off. but nothing to hard.

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Rezz
      Gran Turismo 7 Time trial

      By Rezz · Posted

      Does this count as a time trial as well? I got all gold in the master super licence (1 lap time trial) and received a McLaren MP4/4 for my trouble.  If anyone else has done this, did you ride the wall right around the first long right hander at Lake Louise snow track to get gold? I couldn't do it any other way... best I could do without riding the was was within 2 tenths of the gold time.
    • MBS206
      MLR's Bogan cruise ship

      By MBS206 · Posted

      I definitely get the low power, sporty car to drive to smash gears but not be doing eleventy million miles an hour! It makes all the normal drives fun!   Rev match tune sounds like the funs! I didn't know the NC had a DBW throttle!   As for me, still have the Skyline, it still has the Barra in it. It's been pushed to the side of the workshop at the moment. Pretty much waiting on me finishing the wiring, and dropping new fuel lines in. Got myself an ACDC Tig end of last year so been teaching myself TIG welding to build a few things for the Skyline. The missus wrote off her GTB liberty at the end of last year, and got it back on salvage rights stupid cheap. It's also still registered, so will mean easier for me to take to the track already done most of the panel damage, just playing "clear the workshop" to make space to pull the motor and box out, fix some oil leaks, replace the clutch, and replace a few minor broken things.  Also got a Lathe at the start of the year, which is adding to the annoyance of no space, which is another reason I'm trying to build things to get more space, to get the Lathe back in a final home for it. It's a BIG lathe, can turn a 355mm diameter, and 1metre between centres... Got it at a steal! So between it and the TIG and old MIG welder, I'll be fabbing some fun little shit up But we've had a lot of shit stuff happening at home, so it's slow going getting things done. But one step at a time!
    • PranK
      Gran Turismo 7 Time trial

      By PranK · Posted

      I love Catalunya.  Got a 1:54.632. The AMG is a hoot.
    • Kinkstaah
      Dose's Sometimes DIY and Pay Someone Home & Boat Improvement Thread

      By Kinkstaah · Posted

      I hadn't got that far, my main worry was the connection to the actual calipers themselves. I'm just using new (ish) stock brake lines in the stock setup. I've just had a stud welded to the knuckle that is a little lower than the original stud (so my knuckles have two studs each side) to not have it be stretched so far in previous BBK setups, so the "block" (in the second picture) mounts a little lower for me and I hope I don't need to change anything. I may have even changed the connection to the calipers in the past and have since forgotten I did that. I may not have. Guess how I'm gonna find out. Source: hopium
    • Dose Pipe Sutututu
      Dose's Sometimes DIY and Pay Someone Home & Boat Improvement Thread

      By Dose Pipe Sutututu · Posted

      It's more so I'm using the 1x piece line from HEL that goes from the body to the caliper. There's no middle block/mount like the HFM ones or the GKtech ones. There are certain angles/suspension compression where the line actually slightly contacts the ARB. Below of how mine sit (not my photo): How I want it:  
×
×
  • Create New...