Jump to content
SAU Community

Recommended Posts

with that product do take into account that its designed for different shape licence plates. so the spring tention could be too little.

for rear licence plates ive looked at setting up a air ram or electric solinoid valve for moving that up n down. once ive finished this ill post more. (that could be years knowing me)

My boss told me that you can transmit a certain AM radio frequency that renders a RADAR speed camera (not 3 lines on road) ineffective whilst in range of it. Just a matter of trying it out some how. Older speed cameras that use the 3 lines on the road are not succeptible to such trickery unfortunately.

This technique also works with Porches, by transmitting AM frequencys when your next to a Porche it will shut down its ECU and the driver will have to start the car again. Very effective for drags.

That spray looks pretty good, I had an idea once of putting a high output xenon globe above the number plate that was triggered off by a flash sensitive device...... hopefully in time to blind the camera.

Alternatively you could use solenoids to flip your number plates up and down using a switch inside the car.

So many ideas....... mwaahahahaha ;)

akeenan if you do a good ennuff job of the flippers etc etc then its really going to *** with his head.  

most likely get a sticker, but if the plates couldnt be moved when he tried to move then he would be left really confused.

except for the common fact that police browse these forums and are now aware of these devices i think youd be in a bit of trouble.

Guest
This topic is now closed to further replies.


  • Similar Content

  • Latest Posts

    • Check the injectors flow evenly, and are actually flowing what you and the ECU think they should be flowing. If it's starting up on starter fluid, you have a fuel issue. Is it possible under cranking your fuel pump is turning off?   The harness you replaced, is that the whole engine harness? Do yourself a test, and drop the old harness on and plug it into the Z32 ECU. It's possible they've wired things different. From memory S1 to S2 is different in RB25 and you may have a wrong loom
    • I haven’t pulled the injectors to watch them spray yet but they are clicking from the cas and all of the spark plugs are wet with fuel. I’ve thought the cylinders were being flooded from the beginning and was hoping fuel pressure would fix it. Tonight I am going to pull the rail and watch the injectors spray. Don’t know how to test/diagnose if the plugs are firing in correct sequence but that should be a timing thing and as far as timing goes my car still has the half moon for the cas can only install it 1 way. And my mechanical timing is 100% correct I posted photos above. Confirmed with the balancer on and off. 
    • I checked spark on all cylinders and they all visually have spark with the plug pulled and grounded, but plug 1 is the only one that fouled. This was a running swap that blew up and was rebuilt by a machine shop, put a new wiring specialties harness and did all gaskets, studs, and bolts while it was out.  compression is 135-150 across all cylinders. Aside from that from my understanding with the z32 ecu and maf the car should start regardless. The wiring for TPS and the dual 02 sensor/ dual knock sensor stuff shouldn’t actually stop the car from starting or even running well, (just slightly rich)  they just give fault codes. Car supposedly is supposed to start as long as you have z32 afm and ecu with the nistune base map and that’s info coming from a well known and trusted tuner who does a lot with SR/RB (Rsenthalpy). After more trouble shooting today where I’m at right now is that the cas is sending signal to the injectors they click while spinning the rotor, Fuel pressure is now set at 43psi, all cylinders have good compression and all of the plugs looked great (just wet with fuel) except for cylinder 1 which was very black (cylinder 1 has 150psi compression). all of the coils generate spark if pulled out and grounded out on the head. On the fuel pump car just pops into the exhaust. On starting fluid car will fire off. Hard to tell if all cylinders are firing off but definitley a couple. sounds like all of them but it’s only for 3-5 seconds hard to tell. 
    • Final update!!! Got the front bar fitted and sprayed and all sorted now. My cutouts worked great and the indicators aren’t just falling off. 😂  
×
×
  • Create New...