Jump to content
SAU Community

Recommended Posts

I've had issues with a new bosch 040 in my R33. It ran fine for a day but the pump fuse blew. I changed the fuse and the car started but when i tap the throttle there is a whirring noise coming from the boot (similar to priming) lasting a couple of seconds, and if i tap it a few times i hear the pump 'click' and the car shudders so i have to switch it off.

Does this sound like an issue with the pump/voltage regulator?

I was going to take it to Unigroup tomorrow and get it tested and reinstalled (it's already booked) but i doubt the car will make it out of my driveway.

Anyone know a mobile auto-electrician who knows Skylines? I'm near Parramatta.

Cheers

Edited by R338OY
Link to comment
https://www.sau.com.au/forums/topic/209068-fuel-pump/
Share on other sites

(Factory)Wire gauge is to small for your upgraded pump(it uses more power).

Needs a fresh run of thicker electrical wire, coupled with a relay to turn pump on/off.

Parts/wire shouldn't cost more than $40, labour will be more expensive, up to 2-3 hours for those not familiar with skylines.

Edited by infamous_t
Link to comment
https://www.sau.com.au/forums/topic/209068-fuel-pump/#findComment-3696880
Share on other sites

You paid a punk to install it, its his issue man! lol

Need more info, and as you didn't install it, ppl be stabbing wildly.

Unigroup seems pretty good, Yavuz will sort you out man.

Get to organizing that tow man for tomorrow man :)

Yeah Yavuz has worked on the car before. Spoke to him today and he's doing me a favour to look at it! Worst case scenario i'll have to tow it :D

(Factory)Wire gauge is to small for your upgraded pump(it uses more power).

Needs a fresh run of thicker electrical wire, coupled with a relay to turn pump on/off.

Parts/wire shouldn't cost more than $40, labour will be more expensive, up to 2-3 hours for those not familiar with skylines.

That sounds pretty convincing to me. I thought it might be $2-300 labour to call someone out, plus other bits and pieces.

So is it better to call someone out or try get it to the workshop? I'm more confident in Unigroup because Yavuz knows Skylines very well.

Anyone have a contact?

Thanks for the advice.

Link to comment
https://www.sau.com.au/forums/topic/209068-fuel-pump/#findComment-3696929
Share on other sites

Getting some proper copper to an after market pump in a Skyline is key, but i wouldn't thi... wait..

You have a R33, the battery's already 100cm away from the pump :ninja:

Make sure you let us knows what the issue was :)

Will do lol :happy:

If anyone has a contact let me know. It'll save calling some random electrician.

Edited by R338OY
Link to comment
https://www.sau.com.au/forums/topic/209068-fuel-pump/#findComment-3697118
Share on other sites

Getting some proper copper to an after market pump in a Skyline is key, but i wouldn't thi... wait..

You have a R33, the battery's already 100cm away from the pump :(

Id don't own a 33 to verify myself, but I would imagine the signal still comes from the ecu, which is still up the front of the car.

I forgot about this myself, but should make parts total cheaper (less cable).

Good luck mate :(

Link to comment
https://www.sau.com.au/forums/topic/209068-fuel-pump/#findComment-3699813
Share on other sites

Omar,

What time will you be at Unigroup?

Im heading there friday around 11am.

Yavuz and the team look after my boat, he'll get it sorted.

I've got a Walbro in there, few months back I had some mods finished and my fueling system was playing up.

Turns out that it was the low/high voltage for the fuelling.

I dont know too much on it, but apparantly when the car is at idle, it used a low voltage sender and when it gets up and going, uses the higher voltage. Mine was having dramas with that dual voltage and now it just runs on the high.

I cant notice any difference but fixed the issues.

:domokun:

Cheers,

Chris

Link to comment
https://www.sau.com.au/forums/topic/209068-fuel-pump/#findComment-3700120
Share on other sites

Well after frying 5 fuses to get to Unigroup (distance- 3 min drive) i finally had it looked at. Turns out the positive wire on the pump had been squashed between the pump bracket and tank. The reason it drove fine at first was because the wire wasn't grounding on the tank- until bumping around cut into the wire and lead to the shorting out.

All it needed was a zip tie to hold the wires in place and careful reinstallation. 30 mins labour and the car drives fine and revs out nicely :thumbsup:

Omar,

What time will you be at Unigroup?

Im heading there friday around 11am.

Yavuz and the team look after my boat, he'll get it sorted.

I've got a Walbro in there, few months back I had some mods finished and my fueling system was playing up.

Turns out that it was the low/high voltage for the fuelling.

I dont know too much on it, but apparantly when the car is at idle, it used a low voltage sender and when it gets up and going, uses the higher voltage. Mine was having dramas with that dual voltage and now it just runs on the high.

I cant notice any difference but fixed the issues.

:)

Cheers,

Chris

Hi Chris, i got there yesterday arvo, about 6pm. If i went today you'd be able to see how annoyingly minor the issue was! :P

Good to hear you sorted your voltage out- is the dual system going bonkers a common thing? Does the car just run sluggish with this problem? I'd like to know so i can recognise the signs.

Cheers mate

Edited by R338OY
Link to comment
https://www.sau.com.au/forums/topic/209068-fuel-pump/#findComment-3700940
Share on other sites

Omar,

Mate unfort I couldnt tell hey!

When it was on the dyno for final tuning, thats when the problem occoured.

So yeah, sorry I cannot give you a better answer mate! ;)

No worries mate, but cheers for the info. If i ever get the same problem you'll be first to hear about it!

Doh - amateur hour

Going to let us know who did the work, so we can boo them :spank:

jk, don't do that.

Lol. Yeah guess that's the DIY risk- but i don't mind :cool:

The mate who installed it came along and Yavuz gave him a little booing for soldering the terminals. Hehe i thought he was about to clip him over the ear :D

Link to comment
https://www.sau.com.au/forums/topic/209068-fuel-pump/#findComment-3702063
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeah, it's getting like that, my daughter is coming over on Thursday to help me remove the bonnet so I can install the Carbuilders underbonnet stuff,  I might get her to give me a hand and remove the hardtop, maybe, because on really hot days the detachable hardtop helps the aircon keep the interior cool, the heat just punches straight through to rag top I also don't have enough hair for the "wind in the hair" experience, so there is that....LOL
    • Could be falling edge/rising edge is set wrong. Are you getting sync errors?
    • On BMWs what I do because I'm more confident that I can't instantly crush the pinch welds and do thousands of USD in chassis damage is use a set of rubber jacking pads designed to protect the chassis/plastic adapter and raise a corner of the car, place the aforementioned 2x12 inch wooden planks under a tire, drop the car, then this normally gives me enough clearance to get to the front central jack point. If you don't need it to be a ramp it only needs to be 1-1.5 feet long. On my R33 I do not trust the pinch welds to tolerate any of this so I drive up on the ramps. Before then when I had to get a new floor jack that no longer cleared the front lip I removed it to get enough clearance to put the jack under it. Once you're on the ramps once you simply never let the car down to the ground. It lives on the ramps or on jack stands.
    • Nah. You need 2x taps for anything that you cannot pass the tap all the way through. And even then, there's a point in response to the above which I will come back to. The 2x taps are 1x tapered for starting, and 1x plug tap for working to the bottom of blind holes. That block's port is effectively a blind hole from the perspective of the tap. The tapered tap/tapered thread response. You don't ever leave a female hole tapered. They are supposed to be parallel, hence the wide section of a tapered tap being parallel, the existince of plug taps, etc. The male is tapered so that it will eventually get too fat for the female thread, and yes, there is some risk if the tapped length of the female hole doesn't offer enough threads, that it will not lock up very nicely. But you can always buzz off the extra length on the male thread, and the tape is very good at adding bulk to the joint.
    • Nice....looking forward to that update
×
×
  • Create New...