Jump to content
SAU Community

Recommended Posts

Item1: JIC FLT Coilovers

Age:Unsure

Condition: Very good condition, was told they were on the car for approx 10,000km

Price: $1050 ono

To Fit: (What car) R32 Skyline

[Comments: Bought it last year (2007) to fit into my use in my car but have since sold the car and have no use for them.

post-19838-1204940494_thumb.jpg post-19838-1204940505_thumb.jpgpost-19838-1204940529_thumb.jpg

post-19838-1204940539_thumb.jpg post-19838-1204940556_thumb.jpg

Item1: Unknown Jap Brand R32 Front and Rear Strut braces

Age:Unsure

Condition: Very good condition

Price: $180 ono for both OR $95 each

To Fit: (What car) R32 Skyline

[Comments: Bought it last year (2007) to fit into my use in my car but have since sold the car and have no use for them.

post-19838-1204940565_thumb.jpg[

Item 3: Stock Front Upper control arms with near new Nolathane bushes

Age:1 year

Condition: Very good conditiononly used to go through regency and used camber adjustable 1s instead

Price: $100ono

To Fit: (What car) R32 Skyline

[Comments:

post-19838-1204940704_thumb.jpg

Location: Adelaide

Contact: Andy: PM or 0434345424

post-19838-1204940517_thumb.jpg

Edited by thanglongz

mite take upper control arms off you next week if u still got em.

just gotta get sum cash

mine are rooted n need new ones soon (hold em for me??)

  • 1 month later...
ill take the rear strut brace, if you dont mind posting to brisbane 4500, at my cost of course

Yea that should be fine mate

ill send you the details on PM

ill take the rear strut brace, if you dont mind posting to brisbane 4500, at my cost of course

Yea that should be fine mate

ill send you the details on PM

  • 3 weeks later...
the coils for r32 gtst or gtr?

Excuse me for jumping in here... But since my knowledge of skylines is limited and I actually know this one I just cant help myself.. :) These are for gtst because gtr rear ones dont have the round mounts with the rubber at the bottom but instead have a square "C" shape with no rubber.. gtr front ones fit gtst but I think they may lower the car slightly.. Thats my 2.2 cents (gst inc.) :thumbsup:

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • OK, Step 3, if you need to remove the valve body, either to replace it, the TCM, or to do a more complete drain.  First, you need to disconnect the TCM input wires, they are about half way up the transmission on the drivers side. One plug and the wires are out of the way, but there is also a spring clip that stops the socket from sliding back into the transmission. On my car the spring clip was easy to get, but the socket was really stuck in the o-ring of the transmission housing and took some.....persuasion. You can see both the plug to remove (first) and the spring clip (second) in this pic Incidentally, right next to the plug, you can see where the casting has allowance for a dispstick/filler which Nissan decided not to provide. there is a cap held on with a 6mm head bolt that you can remove to overfill it (AMS recommend a 1.5l overfill). Final step before the big mess, remove the speed sensor that is clipped to the valve body at the rear of the box.  Then removal of the Valve Body. For this the USDM Q50 workshop manual has a critical diagram: There are a billion bolts visible. Almost all of them do not need to be removed, just the 14 shown on the diagram. Even so, I both removed one extra, and didn't check which length bolt came from which location (more on that later....). Again it is worth undoing the 4 corners first, but leaving them a couple of turns in to hold the unit up....gravity is not your friend here and trans oil will be going everywhere. Once the corners are loose but still in remove all the other 10 bolts, then hold the valve body up with 1 hand while removing the final 4. Then, everything just comes free easily, or like in my case you start swearing because that plug is stuck in the casing. Done, the valve body and TCM are out
    • OK, so if you are either going for the bigger fluid change or are changing the valve body which includes the Transmission Control Module (TCM), first you should have both a new gasket 31397-1XJ0A and a torque wrench that can work down to 8Nm (very low, probably a 1/4 drive one). You can probably get by without either, but I really didn't want to pull it all apart together due to a leak. First, you now need that big oil pan. The transmission pan is 450 long x 350 wide, and it will probably leak on all sides, so get ready for a mess. There are 24x 6mm headed bolts holding the pan on. I undid the 2 rear corners, then screwed those bolts back in a couple of turns to let the pan go low at that end, then removed all the middle bolts on each side. Then, undo the front corner bolts slowly while holding the pan up, and 80% of the fluid will head out the rear. From there, remove the remaining bolts and the pan is off. You can see it is still dripping oil absolutely everywhere...it dripped all night.... I got another couple of litres when I removed the pan, and then another few when I removed the valve body - all up another 4l on top of the 3 already dropped in step 1.
    • Yeh I think i'll message an old contact i had for ages that manages his own tyre shop now.. n tell him what i want n work with him before ordering..  Got this 17x9 +30 Driftteks on 245/45/17 PSR Drag Radials on the rear.. They fit well - for your reference in future - Rear guards  have been lipped in & minimal to non flaring of the rear Gaurds.    
    • If only it were that easy! I also needed to remove seats, shocks, brake calipers, send my car through a fence, and use measuring and ended up guessing because I didn't remove seats, shocks and brake calipers. It can be hard sometimes Can be a little more complex than 'just measure' if you want to truly measure the entire wheel through all of it's suspension travel. But if you aren't going for every last mm then yeah, you can check the space you currently have and guesstimate.
    • If you own a car, and it has wheels on it, and you know the offset of those wheels, and you have a measuring device, you have everything you need to work out if other wheels will fit.
×
×
  • Create New...