Jump to content
SAU Community

Nistune Powerfc Hks Fcon Haltech Ems Link Ecu Etc Real Time Road Tune And Dyno Tune Available In Sydney And Other State


Recommended Posts

I'm also looking at getting a tune checked/done

My r32 gtst

mods are

Rb20det

Fmic

Rs*r 3.75"

Coil packs

Pod filter

New clutch (heavy duty)

Already has a remapped ecu

How much am I roughly looking at?

Thanks.

  • 3 months later...

Hi Toshi,

I know I asked ages ago, but I'm starting to more seriously look at getting this done - am saving now.

My car is:

R33 GTST S1

stock turbo, stock injectors

Apexi AVCR

3" turbo-back exhaust

FMIC

I'd need the Z32 ECU with Nistune board supplied - so basically I'd turn up with my car as is, and get the ECU replaced and tuned by you - how much would that be in total so I know how much I need to have in cash?

Thanks mate!

  • 4 weeks later...

Toshi,

I want a Z32 Nistune ECU with a pre-loaded map for:

R33 Gts-t Manual

Full 3" turbo back

R34 SMIC

GT-R Fuel pump

Stock tubro, stock injectors.

Can you quote me for supply of this? ETA if I order?

Would I need to get a dyno tune to check AFR's etc after fitting?

  • 3 months later...

I am often asked how much power increase about E85 TUNE.

Power is around 30kw more than 98 octane fuel.

I recommend Bosch 1000cc injector because much better spray than hiflow injector.

  • 4 months later...

Hey toshi quick qoute mate

R33 s1.5

Hypergear atr43ss2 turbo

Fmic

750cc bosch injectors

255lph walbro fuel pump

Greddy style plennum with std throttle body

Z32 afm

3inch turbo back exhaust

Power fc

May have to get the plennum and injectors fitted

Edited by cav33r
  • Like 1

Hi cav33r

Price $550 road tune $600 dyno tune only $700 dyno tune and road tune both.

Hi soulfood187

If come weekday you can come any time.

  • 1 year later...



  • Latest Posts

    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
    • Pull codes via the self-diagnosis procedure. As far as I can tell this is just a sign of transmission issues but not a code unto itself.
    • Hi All, putting the engine back together and everything is perfect except have this plug left over.. any ideas what it is for and where it goes? Is on cold side under the intake plenum *note not a stock plug, as everything has been modified Cheers
×
×
  • Create New...