Jump to content
SAU Community

Recommended Posts

Hey guy,

I have just put my thermo fan in the car but i haven’t yet hooked it up to the power. Has anyone else put one in a r32?

My poor little bnr32 seized up the clutch fan. :D

I want to know if i should just hook it up to a switch in the cabin or not?(manual turn on and off)

Regards Keith

Link to comment
https://www.sau.com.au/forums/topic/210153-thermo-fans/
Share on other sites

I've got two switches hooked up on mine. One to the ignition, the other is a thermo switch (turns on when it reaches a certain temp). Each fan runs one relay.

I've got two thermo fans, 1x shrouded 14inch fan, and 1x 12inch fan unshrouded (no space due to aircon).

Wiring would be the same between any car.

Link to comment
https://www.sau.com.au/forums/topic/210153-thermo-fans/#findComment-3717346
Share on other sites

I use a 14" thermo with the standard shroud, its controlled by an electronic thermo switch that reads from the standard sensor in the thermostat housing...

Ive never had over heating issues since I started using this set up, I have the switch set to 84 degrees and even on a hot day it doesnt go over 91 maximum.

The best thing about removing the engine fan is the increase in engine response, by taking off the standard fan you reduce parasitic drag on the engine by quite a lot which makes it much easier to rev.

Link to comment
https://www.sau.com.au/forums/topic/210153-thermo-fans/#findComment-3720084
Share on other sites

  • 1 month later...

Have fitted plenty of these to GTRs and GTSTs. The main thing is to make sure that the radiator is a twin core one as the late version gtst had single core and don't seem to work efficiently with thermo's.

As for wiring, the best way is to use a thermo switch to control them. These can be as simple as a probe that sits underneath your radiator hose or a fan switch that is tapped into your manifold or a adaptor in your hose.

I usually go for the first as it is easiest, but have used both with good results.

Do not rely on manual switches as there will come a day when you will forget.

As for wiring it you will need either two relays or the one i use is a 70amp one that you can run both thermos from(much easier and less wiring)

Here is a brief description of how it wires in.

The thermo switch turns the relay on by giving it a earth when it reaches it preset temp and the relay then turns on both thermo fans.

Put the thermos behind the radiator in between the radiator and engine as they cause an airflow restriction when they are in front. You can use two 12" which are actually 13" in total diameter and these will fit perfectly or you can run 2 13" by overhanging them and blocking the sides in so they can only suck through the core.

Make sure you stagger them so that one thermo sits to the top and one sits to the bottom of the radiator, and also make sure they are wired and fans are spinning the right way to pull air instead of pushing air.

If you need a diagram drawn i would be happy to or i can show you how i do it as i am doing one for a customer at the moment.

Link to comment
https://www.sau.com.au/forums/topic/210153-thermo-fans/#findComment-3806394
Share on other sites

Ok this might sound a bit dodge, but talked with my local auto electrician, and he's a bit of a lateral thinker (does good work) He said I should be able to use EA to BF at least thermo fans? As they all had them from then on? Or commodore ones, just need to measure up the radiator and compare the sizes. He did say commodores had larger thermo fans. Anyone know anything about using falcon or commodore ones? Or should I steer clear of them?

Link to comment
https://www.sau.com.au/forums/topic/210153-thermo-fans/#findComment-3816751
Share on other sites

Ok this might sound a bit dodge, but talked with my local auto electrician, and he's a bit of a lateral thinker (does good work) He said I should be able to use EA to BF at least thermo fans? As they all had them from then on? Or commodore ones, just need to measure up the radiator and compare the sizes. He did say commodores had larger thermo fans. Anyone know anything about using falcon or commodore ones? Or should I steer clear of them?

Member on here with Candy red 32 with 26/30 swears by the EA thermo fans, personally im looking at the flex-a-lite thermos which are a twin thermo in a single casing.

Link to comment
https://www.sau.com.au/forums/topic/210153-thermo-fans/#findComment-3816776
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The car/ECU will have all the sensor that it needs and expect to have. I think i do not have to explain to you how the Link is way better specialy if you have swapped engine   I just do not want to deal with any "problems" cuz i have only Nistune which i learned is not that great and in my case cant even deal with that speed problem (Link can) And of course it will be way more easier to tune and diagnose and safe. And for the ECU/speed problem...i dont know.
    • Per Mark Roberts of Sonictune: Mark Robert Author At this time, no. No ETA either 2016-17 models. You will be able to purchase and install a 2018.5+ TCU though   TCU purchasing and pricing info! As we near the release of TCU tuning, I am going to answer some questions I get asked often.   What do I need for TCU tuning? At this time, you will need a 2018.5+ TCU to be able to tune. If you have a 2016-to early 2018, you will need to replace your TCU with the newer version. One good way to know if your TCU is good is if you have auto upshift in manual mode in 1st gear around 6500 rpms. If your manual 1st gear goes to 7k rpm and will hit the rev limiter unless you shift, you have the older TCU.   Why do I need to buy another ecu license/phone flash if I already have it on my ECU tune? The TCU is its own computer module. It is completely separate from the ECU. Because of this, you will be required to purchase a TCU license and, if your tuner has it, the phone flash license required to tune it via phone/bluetooth.   Do I need TCU tuning? TCU tuning is NOT required. However, the faster your setup, the more it will assist in track and dragy time consistency.   If I’m ECU tuned by (tuner A) can I get my TCU tuned by (Tuner ? Yes, since it’s a different module and a completely separate flash, you can have two different tuners. However, it is highly recommend that you have both tuned by the same tuner. For me, my TCU tuning will directly complement my ECU tuning style and features and running my ECU and another TCU or vice versa MIGHT cause some issues. At this time and for the foreseeable future, I will only be tuning my current ECU tuned customers TCUs.     I have a SYVECS AWD controller. Do I still need it? Yes! The AWD controllers main job is to control your AWD system. However, with TCU tuning, you will no longer need the auto-shift function as that will be done through the TCU. The AWD controller will still be very beneficial for racers looking to maximize traction on the launch.     Shift schedule changes: holding gears longer at lower pedal input as well as max shift rpm changes. Please note, the new ECU race rom coming out will address 90% of the shitty drivability issues these cars have through custom maps from myself and Racebox—as well as others I am sure.   Increase shift speeds: as seen in the videos I’ve been posting, the TCU shifts much faster once tuned.   Increased shift pressures: as also seen in the videos, much firmer full throttle shifts.      
    • Per Mark Roberts of Sonictune:     Mark Robert Author At this time, no. No ETA either 2016-17 models. You will be able to purchase and install a 2018.5+ TCU though   TCU purchasing and pricing info! As we near the release of TCU tuning, I am going to answer some questions I get asked often.   What do I need for TCU tuning? At this time, you will need a 2018.5+ TCU to be able to tune. If you have a 2016-to early 2018, you will need to replace your TCU with the newer version. One good way to know if your TCU is good is if you have auto upshift in manual mode in 1st gear around 6500 rpms. If your manual 1st gear goes to 7k rpm and will hit the rev limiter unless you shift, you have the older TCU.   Why do I need to buy another ecu license/phone flash if I already have it on my ECU tune? The TCU is its own computer module. It is completely separate from the ECU. Because of this, you will be required to purchase a TCU license and, if your tuner has it, the phone flash license required to tune it via phone/bluetooth.   Do I need TCU tuning? TCU tuning is NOT required. However, the faster your setup, the more it will assist in track and dragy time consistency.   If I’m ECU tuned by (tuner A) can I get my TCU tuned by (Tuner ? Yes, since it’s a different module and a completely separate flash, you can have two different tuners. However, it is highly recommend that you have both tuned by the same tuner. For me, my TCU tuning will directly complement my ECU tuning style and features and running my ECU and another TCU or vice versa MIGHT cause some issues. At this time and for the foreseeable future, I will only be tuning my current ECU tuned customers TCUs.     I have a SYVECS AWD controller. Do I still need it? Yes! The AWD controllers main job is to control your AWD system. However, with TCU tuning, you will no longer need the auto-shift function as that will be done through the TCU. The AWD controller will still be very beneficial for racers looking to maximize traction on the launch.     Shift schedule changes: holding gears longer at lower pedal input as well as max shift rpm changes. Please note, the new ECU race rom coming out will address 90% of the shitty drivability issues these cars have through custom maps from myself and Racebox—as well as others I am sure.   Increase shift speeds: as seen in the videos I’ve been posting, the TCU shifts much faster once tuned.   Increased shift pressures: as also seen in the videos, much firmer full throttle shifts.      
    • The fancy pants red shock tower brace is finally incoming from MX5 Mania, getting it shipped from 'Merica has been a long and problematic process, and GWR, the 'Merican supplier will not ship directly to consumers outside of the US, Mania basically had to order a heap of them, the colour choice was silver, or red, and we all know anything red adds 5 killerwasps of dynotorques..... Whilst it does fit over a 2.5, and I've seen a few photos and videos of it being installed and fitting, google also says it might get real close to the FAB9 intake front runner, people in the US says it does fit with the FAB9 intake, except for one person who said it slightly touched.......so there is that.....LOL..... As it seems that I am the first in AU to have this combination of parts there's no local knowledge about fitment, so I'm just a willing guinea pig in this endeavour, I'll cross my fingers and toes and hope for the best In other news, I ordered stuff from China  on the same day I ordered the 23° silicone bend from Victoria, the stuff from China arrived a day ago, the 23° silicone bend is still travelling around Australia thanks to Australia Post, and "may" be here next week
    • Very good news...I contacted Racebox about it last night. My car is a 2016 so remains to be seen if it is compatible, requires a TCU swap, or is impossible.
×
×
  • Create New...