Jump to content
SAU Community

Recommended Posts

The screw aloows you to adjust hte spring tension. When you are running more bosot pressure you might find it starts to leak in higher rev's so you want to tighten the srping up, however if you are not running as much boost you want to loosen it off to ensure the BOV will be able to open. However they more adjustable nowdays for rice factor to get different sounds.

BOV"s are illegal for the reason being that they vent blow-by into the atmosphere... yes they can be noisey, yes they cause the car to run richer but its stated that they blow un-filtered air/oil into the atmosphere... stupid really, cos last time i checked the exhaust vented to atmo aswell?? But thats all good its only carbon monoxides and what have you, alot worse than the 'ocassional' mist of oil comin from a BOV.

P.s. Don't forget BOV's if they aren't a good design will cause crappy throttle response, and having a atmo BOV means you must re-spool that released amount of air. They have their pluses and minuses.

As YBSLO4 mentioned BOVs are illegal if they vent to atmo, because cranck case gasses must exit the car via the exhaust, Road Traffic Act 1962 (from memory) in SA. These traffic laws are now pretty much consistant australia wide. So they MUST plumb back to be legal - like the stock one.

As for adjusting BOV, tighter will mean it takes more (boost) pressure for the valve to lift. Yes it will make less noise, but the fluttering noise you hear is air reversing through the compressor, slowing the turbo down (increasing lag) and putting strain on the turbine - this isnt too good for obvious reasons.

I adjusted mine by winding it back until the fluttering sound was almost gone. Almost, because if you wind it back too far, you may have the car stall at idle as it doesnt seal properly. Something to have a play with until you are happy.

The only noise testing I know of that a car needs to be roadworthy has to do with the exhaust, this is done with the car at revs, and the EXHAUST is not to exceed 89dBs. This is conducted with the car at specific revs, not changing gear - so I am not sure how any copper gets away with defecting cars for excessive intake noise (how could it exceed 89dB?) or noisey BOV which wouldnt be measured if a car was being tested for compliance with noise regulations - only for atmo BOV or pod that doesnt comply with ADRs.

I have heard of people claiming to be defected for this, and I would love to know exactly what regutation/act it is that they would be in breach of?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I can get more photos of it here soon and I plan to make a thread detailing the process. I received the car this way and it sorely needs refinishing. That is probably the most appealing photo of it. Up close it is fading, cracked, and needs to be re-glued. Depending on their condition I'm on the fence between refinishing or making a new set.  Another angle hiding the pimples and razor pumps  
    • According to this thread the RS4V with build plate RC40 comes with the R200 diff @ 4.083 ratio as well (mine has said RC40 denotation). We may need to check if the axle stubs are the same pattern as well. The auto subframes have longer axles. However I think yours being a later Series 2 as well, we should have the same bolt pattern for the diff stubs. Unless your upgraded rear also has upgraded axles. Either way, I would not be opposed to pulling the covers to check so I can inspect that  fancy rear core  Also I don't have HICAS. I don't believe that should change things but I hope the people here with heaps more experience than me can correct me if I'm wrong   Let me know if you want to attempt to make this work and I can get some pictures of mine from under the car. 
    • It's not that straightforward. For example I have had this code because my ignitor/power transistor wires were unplugged. It knows something is wrong but has no idea what it means. If you want to actually diagnose this I recommend following the service manual flowchart for code 21. Ohm out the harness, coilpacks, inspect the ECU, etc. And again, it's entirely possible for there to be no problem at all but if you're running a different coilpack it'll trigger the code because it doesn't like what it sees.
    • If it (the code) wasn't still current, it should have gone away by itself by now. No, nothing it 10/10. But it is quite likely. Everything else to do with the ignition could still be responsible (which is wires and connectors). The car is an old piece of shit now, so all the wires and connectors are also old pieces of shit.
    • Lock me in mate, although I'm not sure if I'll be heading up from Goulburn or down from Sydney, either way, return will be back to Goulburn 
×
×
  • Create New...