Jump to content
SAU Community

Recommended Posts

lol i thought this might be interesting duno if theres a topic about this but I have heard too many people that argue both sides for different reasons.

So what do you think? After a job well done under your bonnet, do you hold n drop ur bonnet or do you gently press it till it locks in?

get the comments goin!

Link to comment
https://www.sau.com.au/forums/topic/210421-drop-ur-bonnet-or-press-ur-bonnet/
Share on other sites

lol i thought this might be interesting duno if theres a topic about this but I have heard too many people that argue both sides for different reasons.

So what do you think? After a job well done under your bonnet, do you hold n drop ur bonnet or do you gently press it till it locks in?

get the comments goin!

Drop it!!!! but only from a few inches up. :domokun:

I've got a standard bonnet and press it down. It's stock so as long as you're not pressing it down from the middle then it should be fine.

I've heard somewhere about fiberglass bonnets cracking from pressing down?

i drop mine, coz my panel beater told me that he has seen big hand size dents on bonnets coz people press on them.

but what about the boot? :P do you guys drop it or press it?

i drop mine too...

Drop if its a GTR, my spring tension is a little high on clip, so I drop it from a little higher than most recommend, 5-7in is about right for me.

Its funny when you go to lift a non GTR bonnet, its so damn heavy in comparison you think its still locked :P

I push mine, but i make sure i have one hand either side so its not pushing down in the middle. Mines CF but so i doubt it would dent like a standard one...? Otherwise drop from a small height. Boot i have to almost slam shut otherwise it pops open.

yeh boot drops easy. i would of thought that pressing ur bonnet in the middle would be the best spot... or are you's talking about the actual centre of the bonnet. Im think where the catch lock is put ur hand on that, shouldnt bend huh. I can imagine pressing from one of the font corners, stuff that.

I wana lift up a GTR bonnet now. sounds very lite. I can do shoulder press with my bonnet. Gona open up a new gym, no weights just skyline bonnets. haha

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • Yes sir am asking is there possible way from aem tuner from wiring pins 
    • Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...