Jump to content
SAU Community

Anzac Day Cruise + Bbq Sesh (friday April 25th)


Recommended Posts

I'll Probably come down with Chuckie...... can't believe the last meet point.... I could walk home from there!!

It's very kid friendly too though. What sort of time do you envisage being at Manning lake?

It's actually off Hamilton Road. Behind Dalmatinac Soccer club. My Mrs will probably join us there if not too late.

See map.

post-30601-1207053216_thumb.jpg

I'd say about 2:30 to 3. :P

  • Replies 48
  • Created
  • Last Reply

Top Posters In This Topic

I'll Probably come down with Chuckie...... can't believe the last meet point.... I could walk home from there!!

It's very kid friendly too though. What sort of time do you envisage being at Manning lake?

It's actually off Hamilton Road. Behind Dalmatinac Soccer club. My Mrs will probably join us there if not too late.

See map.

post-30601-1207053216_thumb.jpg

haha mate we probably live 2 seconds away from each other, I never see u drivin around tho..

  • 2 weeks later...

I'll post this on Tuned Wa's forum if u want Magic. So we can have some more chicks come on the cruise.....me and doz are pretty much the only girls on our cruises lol.

Angr33 x

Wat time do u reckon u'll get to the final meet point, i did something silly and didnt realise it was this friday and planned something. I'll try change it around but if not, i'll just try meet u there. Thanks Magic

There's no meet, I'll leave it up to you guys to organise it.

You guys would know NoR better than I would.

The freo meet is past the left bank hotel and left into the carpark opposite Leeuwin Barracks.

We're leaving mandurah at 12.30, so I'd say would leave Rocko around 1.10-1.15pm, then arrive at Freo around 1.45 or so? Meaning we'd arrive at Dalmatinac Park about 2.30 or therebout.

Edited by Magic

A lot of ppl have been pm'ing me regarding 2moro. Think we may have more than expected coming (a good thing :) ), but If at all possible can each 'group' of cars your coming with (eg. u and 5 other cars who are mates of yours) please contribute a pack of snaggers. They will all be shared but I just don't want some ppl having 1 snagger, others none, others 4 lol. :(

As Clint said, we would love it if you guys joint us from the very beginning in Mandurah, but I understand some ppl have other commitments prior, so whenever possible is better than not at all. :P

Thanks and hope to see you there. Up for some great weather for a great day. :)

Edited by Magic
Not that I know of. Go for it man.

Just tell them to email me if they have further queries [email protected]

Thanks Niran!

hey dude

no problems aye. yer i put it on silvia wa just then and gave them your email..

best of luck man, hope its a good turnout

have a good one niran

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I wanted to try and preserve the front bumper as long as possible, they're not cheap and are made to order in Japan. Taking inspiration from my previous K11 Micra build where I made an undertray for the Impul bumper, I did the same for this BN Sports bumper but a little slimmed down.  This time round I only made a 'skid plate' (if that's the correct wording/term) for just the bumper surface area, the Micra version covered the gap like an undertray. Starting off with a sheet of mild steel approx. 0.9mm thick 4ft x 2ft in size. I traced around the bumper, cut it out and cleaned the edges. Luckily I was able to get two halves from one piece of metal In the video I installed it as is, but I've since then I've removed it to spray and add a rubber edging trim. The rubber trim is suitable for 1-2mm and it's a really nice tight fit. The bolts had to be loosened due to the plates being too tight against the bumper, the trim wouldn't push on I used some stainless M6 flat headed bolts for a flusher finish (rather than hex heads poking down), I believe this style fastener is used for furniture too incase you struggle to source some. The corner's are a little wider, but this may be an advantage incase I get close to bumping it  The front grill got some attention, finally getting round to repairing it. Upon removal one fixing pulled itself out of the plastic frame, one side is M8 that fixes inside of the frame, where as the other side is M5. Not knowing I could get replacements, I cut down an M8 bolt, threaded it inside the frame along with a decent amount of JB Weld.  The mesh was replaced to match the bumper. One hole on the bonnet/hood had to be drilled out to 8mm to accommodate the new stud, once the glue had set it could be refitted. I think the reason the grill was double meshed was to hide the horn/bonnet latch (which makes sense) but I much prefer it matching the bumper Bumper refitted and it's looking much better IMO The Youtube video can be seen here: https://www.youtube.com/watch?v=bVZP35io9MA
    • The video for the servicing and fuel filter change can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44 One of the main jobs I wanted to do before the car officially went on the road, was to remove the awful looking blue silicone hoses. There's nothing wrong with having coloured silicone hoses, but I realise as I'm getting older I prefer monotone engine bays with a splash of colour on the engine cover(s). I cover this in a lot more detail in the Youtube video, so unfortunately there's limited photos of the process. The intercooler, upper radiator, boost vacuum and upper breather hoses were all changed to black silicone with mikalor clamps. The only blue left is a blanking cap at the back of the inlet manifold and the GReddy pulleys (which will be replaced for stock when the cambelt gets replaced) While the intercooler pipes were off I gave them a quick clean/polish too A before photo I do have a replacement air filter on its way. Fuse box covers were painted blue, they're now satin black Another job on the list while the bumper was off, is to add some mesh https://live.staticflickr.com/65535/54737966256_99b28bfa30_c.jpg[/img] I was hoping to use some thin wire to secure it, but it seems I've misplaced it and the wire I had was too thick to twist easily. I ended up using cable ties for the time being https://live.staticflickr.com/65535/54737131882_c2b7989dcc_c.jpg[/img] Was pleasant to see this https://live.staticflickr.com/65535/54737131627_8b2aab13b3_c.jpg[/img] The last thing to do was to fix the front grill and re-mesh that to match but I ran out of time The Youtube video can be seen here: https://www.youtube.com/watch?v=R4FsF6tgizE&t=23s
    • Hi all,I already introduced myself in the Victoria section, but only saw this section now lol XD New to forums and new to skylines. Hoping to buy my new skyline within October
×
×
  • Create New...