Jump to content
SAU Community

Recommended Posts

Ok so ive got an r32GTR with the standard 16x8 +30 with 225/50

and ive just bought a set of rims that are 18x9.5 +25 and from ive read everyone with these size and offset rim has got 255/35's but i was under the impression that with each inch in rim size you go up that you go down 5 series accordingly... as example 16 has 50 standard and 17 has 45 so i assume that 18 would be 40 series? so why does everyone have 18inch rims but have 35 series tyres? whats the go? please explain? wouldnt it put the speedo out?

Link to comment
https://www.sau.com.au/forums/topic/212166-what-tyres-do-i-need/
Share on other sites

theres no rule that you go down in series by that much for every inch, although it may appear often.

its the whole rolling diameter that affects the speedo not just the profile of the tyre, use an online tyre size calulator and you can work out the best size for your car.

I thought standard tyres were 55 profile.

As a "rule of thumb" (a very rough guide), you should be running a 35 profile on 18" rims (10 units profile per inch change in wheel diameter). But, as Taleb said, you then need to start checking more definitively as to the exact tyre size that gives the right rolling diameter. But I would start in the 35 profile sizes.

The middle number in tyre measurments represents that tyres aspect ratio, its not a measurment in mm... For example - 265 / 35 R18 = 35% of the tread width (approx 265mm) equals the height of the sidewall, therefore you have to factor in the tyres width and aspect ratio together to get the overall diameter.

If you are changing from a 225 / 50 R16 with an approximate o.d of 631mm to an 18" tyre that needs to be wide enough for a 9.5" rim then your best bet is a 255 / 35 R18 (although it will be a little streched on a 9.5") which will have an o.d of about 653mm, this will help to keep your speedo and gearing as close to factory as possible.

Note: Overall diameters will change from brand to brand, as tyre sizes and o.d's are only comparable within each brand so do some checking before you buy.

I hope this helps :)

oh ok, i understand what you mean..

so what tyre would be best? ive gotten prices for a few, Falken, Kuhmo, and nankang in a 255

so would you suggest i get a 265?

as it is i figured 255 is big enough + i dont want to have to modify the car to fit the rims so im hoping it all works out..

i seen in the other thread that people with 255*35*18 could fit with out mods.. so i hope that works for me..

my other concern is that my car is low..

I would suggest fitting the rim to the car without a tyre on it to see how close it will be to the guard (obviously dont lower the car down onto the ground though :pwned:).

Then if you have enough room go for the 255's because they will be as close to standard overall diameter as you will get, the other benifit will be that the walls will lean inward slightly giving you a bit more clearance.

As for brand of tyres - Federal 595's are a great tyre for the right price (Im a bit bias though), 595's are excellent for dry traction and they arent overly expensive, I use them and have all my friends using them and the only complaint I have had is from a mate of mine who goes drifting - he said that they grip to much ;)

Have a look at www.federaltyres.com.au

yeh true ill do that.. as for the federals what are they worth.. ill have to make some calls,

ive been looking at the falken and kuhmo's..

are the federals good on wear.. and what are they like in the wet?

Shop around, you might find a dealer that will look after you on four tyres, use the dealer locator on the website to find one in your area.

The 595's will normally last for about 20 - 25,000kms but if you look after them theres no reason that you shouldnt get 30,000kms from a set.

As a dry traction tyre the 595's are excellent, in the wet they are not bad either, I find them to be pretty predictable and controllable in the wet and if you dont have a lead foot they will disperse the water pretty well and provide good traction.

:)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Did this end up working? Did you take some pictures?
    • And finally, the front lower mount. It was doubly weird. Firstly, the lower mount is held in with a bracket that has 3 bolts (it also acts as the steering lock stop), and then a nut on the shock lower mount itself. So, remove the 3x 14mm head bolts , then the 17mm nut that holds the shock in. From there, you can't actually remove the shock from the lower mount bolt (took me a while to work that out....) Sadly I don't have a pic of the other side, but the swaybar mounts to the same bolt that holds the shock in. You need to push that swaybar mount/bolt back so the shock can be pulled out past the lower control arm.  In this pic you can see the bolt partly pushed back, but it had to go further than that to release the shock. Once the shock is out, putting the new one in is "reverse of disassembly". Put the top of the shock through at least one hole and put a nut on loosely to hold it in place. Put the lower end in place and push the swaybar mount / shock bolt back in place, then loosely attach the other 2 top nuts. Bolt the bracket back in place with the 14mm head bolts and finally put the nut onto the lower bolt. Done....you have new suspension on your v37!
    • And now to the front.  No pics of the 3 nuts holding the front struts on, they are easy to spot. Undo 2 and leave the closest one on loosely. Underneath we have to deal with the wiring again, but this time its worse because the plug is behind the guard liner. You'll have to decide how much of the guard liner to remove, I undid the lower liner's top, inside and lower clips, but didn't pull it full off the guard. Same issue undoing the plug as at the rear, you need to firmly push the release clip from below while equally firmly gripping the plug body and pulling it out of  the socket. I used my fancy electrical disconnect pliers to get in there There is also one clip for the wiring, unlike at the rear I could not get behind it so just had to lever it up and out.....not in great condition to re-use in future.
    • Onto the rear lower shock mount. It's worth starting with a decent degrease to remove 10+ years of road grime, and perhaps also spray a penetrating oil on the shock lower nut. Don't forget to include the shock wiring and plug in the clean.... Deal with the wiring first; you need to release 2 clips where the wiring goes into the bracket (use long nose pliers behind the bracket to compress the clip so you can reuse it), and the rubber mount slides out, then release the plug.  I found it very hard to unplug, from underneath you can compress the tab with a screwdriver or similar, and gently but firmly pull the plug out of the socket (regular pliers may help but don't put too much pressure on the plastic. The lower mount is straightforward, 17mm nut and you can pull the shock out. As I wasn't putting a standard shock back in, I gave the car side wiring socket a generous gob of dialectric grease to keep crap out in the future. Putting the new shock in is straightforward, feed it into at least 1 of the bolt holes at the top and reach around to put a nut on it to hold it up. Then put on the other 2 top nuts loosely and put the shock onto the lower mounting bolt (you may need to lift the hub a little if the new shock is shorter). Tighten the lower nut and 3 upper nuts and you are done. In my case the BC Racing shocks came assembled for the fronts, but the rears needed to re-use the factory strut tops. For that you need spring compressors to take the pressure off the top nut (they are compressed enough when the spring can move between the top and bottom spring seats. Then a 17mm ring spanner to undo the nut while using an 8mm open spanner to stop the shaft turning (or, if you are really lucky you might get it off with a rattle gun).
    • You will now be able to lift the parcel shelf trim enough to get to the shock cover bolts; if you need to full remove the parcel shelf trim for some reason you also remove the escutcheons around the rear seat release and you will have to unplug the high stop light wiring from the boot. Next up is removal of the bracket; 6 nuts and a bolt Good news, you've finally got to the strut top! Remove the dust cover and the 3 shock mount nuts (perhaps leave 1 on lightly for now....) Same on the other side, but easier now you've done it all before
×
×
  • Create New...