Jump to content
SAU Community

Recommended Posts

For Sale:

* 4x Enkie RPF1 17x9.5 +18 5 Stud - months old no scratches or anything look brand new. pretty rare never seen them with good offset in australia before. They fit with no spacers on the front with coilovers. Will fit under standard guards with some guard rolling and camber.

Pics on car are with 0 camber rear and 2.5 neg on the front with 30mm guards

These are very light, weigh in at just 7kg's each

Comes with FED 595's on the front only used for a week. And pretty used maxxis tyres on the back

$1800

* 4x Drift Teks 17x9.5 +18 5 Stud 2 of them have been powder coated white and 2 are still bronze. They have a few scratches.

$900

* Sard 550cc Injectors suit SR Been cleaned and new o rings at the start of the year

$350

Work wheels 18x9.5's +2 just a pair freshly painted black

$400

Blitz Nurspec Cat back exhaust

$250

Garrett gt28rs Disco Potato, used for a few months, no shaft play. 0.86 rear housing. with exhaust manifold and split dump pipe. Braided oil feed line, and stock water lines. Has aftermarket oil drain flange from GCG with the line too

$1000

BBS Meshies - 17x8 +35 5 stud offset pair only have driftable tyres on them

$130

Pics:

IMG_0839small.jpg

IMG_0838small.jpg

IMG_0836small.jpg

IMG_0837small.jpg

enkei_rpf1_silver.jpg

Image000-1.jpg

06042008.jpg

0604200w.jpg

Image007-2.jpg

Image006-1.jpg

05042008a.jpg

07042008.jpg

07042008-1.jpg

12042008-1.jpg

12042008.jpg

10042008-1.jpg

10042008.jpg

Location: South Brisbane

Contact: 0401151011 or pm

Edited by Waldo

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • ok so if i wanted to go 18's i would go for 8's  in front 30+ or 32+ off set at front and the back 9 would be ok? what offset should i aim for.. then can i do some  hunting for wheel rim choices..    If i get this - will this fit all around: Size: 18 x 8.5 +37 - n what tyres size tyre should i get for front n back?  
    • Absolute f*cking nightmare. I had to take breaks constantly, and I was always pissed off when I got home. The line split in Italy on day 2 (we drove from the Netherlands), lol. Driving any narrow European town was... well, sh*t.   Appreciate it man. Here, I'll just drop a favourite from the load I took on Saturday.   I'll update here when things happen with the car, the thing is, with stock power and almost everything chassis-wise taken care of, there really are no problems. 268,000kms now and counting.  
    • Ah! I actually managed to snag a lightly used set.... that aren't so suitable for me right now. They don't work on a GTT without some cutting or creative heat moulding. I thought about reselling them myself cause I didn't want to murder them, but it looks like I'm probably going to attempt to murder them/melt them because I may as well. @GTSBoy @PranK can somebody close this thread?
    • Hey mate,  I have a set, one is slightly damaged but wont be noticable once installed.  Shoot me a message if your still after them 
    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
×
×
  • Create New...