Jump to content
SAU Community

Recommended Posts

Am I the only one who thinks this is a bit of a shitty entry list? Come and race similar cars to yours and have a great day in the sun at WSID. If you're not keen to race then come and watch and cheer on the SAU contingent.

As at 4.30pm March 27, 2008 - Pre-Entrants - 10

Class First Name Surname State Make Model

SF Anthony Howell NSW Holden Barina

SR Adrian Hodgson NSW Nissan Skyline

SR Robert Fearn NSW Nissan Skyline

SR Shane Crichton NSW Toyota Cressida

SA Jordan Vlotis NSW Audi RS6

ST Gary Halpin NSW Dtasun 1200 Coupe

ST Rodney Spannenberg NSW Mazda RX7

ST Steve McGirr NSW Mazda Coupe

SM Jim Whitehurst NSW Holden VL Commodore

OSB Dave Gilbert NSW Suzuki GSXR

Link to comment
https://www.sau.com.au/forums/topic/212904-compak-attack/
Share on other sites

  • Replies 114
  • Created
  • Last Reply

Top Posters In This Topic

Am I the only one who thinks this is a bit of a shitty entry list? Come and race similar cars to yours and have a great day in the sun at WSID. If you're not keen to race then come and watch and cheer on the SAU contingent.

As at 4.30pm March 27, 2008 - Pre-Entrants - 10

Class First Name Surname State Make Model

SF Anthony Howell NSW Holden Barina

SR Adrian Hodgson NSW Nissan Skyline

SR Robert Fearn NSW Nissan Skyline

SR Shane Crichton NSW Toyota Cressida

SA Jordan Vlotis NSW Audi RS6

ST Gary Halpin NSW Dtasun 1200 Coupe

ST Rodney Spannenberg NSW Mazda RX7

ST Steve McGirr NSW Mazda Coupe

SM Jim Whitehurst NSW Holden VL Commodore

OSB Dave Gilbert NSW Suzuki GSXR

no i think its a shitty list too...

Link to comment
https://www.sau.com.au/forums/topic/212904-compak-attack/#findComment-3760849
Share on other sites

Real Name: Jordan Vlotis

Known Username(s): DESCR8, TIKUF, GR8NES, MR_RB, Skyline95, GTR_Junkie, NissanFreak, BlownNboosted, CRACKD, RB Engineering, quick500

Names Used: Jordan Vlotis, George Vlotis, Kirrin Vlotis, 'Joe', 'Joe Savva', Nathan Vlotis, Nathan Arthur, Sam, Jerry

Active on these forums: Skylines Australia, Calais Turbo, GTROUK, SDU, OzAudi.com

Email: [email protected]

Email: [email protected]

Email: [email protected]

Email: [email protected]

Email: [email protected]

Email: [email protected]

Email: [email protected]

Email: [email protected]

Email: [email protected]

Email: [email protected]

Email: [email protected]

Mobile: 0424 519 298

Mobile: 0419 818 795

Mobile: 0424 995 627

Drivers Licence No: 12808522

Bank Details: Bank: St. George Bank, Account No: 1372932043, BSB: 112 879

Bank Details: Bank: CBA, Account No: 028014668 , BSB: 062-105

Bank Details: Bank: ?, Account No: 010323375 , BSB: 062-128

Link to comment
https://www.sau.com.au/forums/topic/212904-compak-attack/#findComment-3763207
Share on other sites

  • 3 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Haha luckily we don't have emissions, inspections, or any laws against power adders here. They only thing they somewhat keep an eye out for are ridiculously loud exhausts. 
    • Just wanted to pop in an update on my setup. The CD swap has been great, I love the mazworks housing for the overall simplicity. I ended up sealing my trans tunnel with a thin sheet of aluminum reused some of the holes on the trans tunnel, and laid some window sealing EPS foam around the edges. Works great, really quieted things down and sealed up the car.  As for the power comment. Right now I am also running about 650whp. with the way the bell housing is attached to the face of the transmission I have zero doubts it would be fine, mainly because the input shaft and main shaft bearings are seated into the bell housing adapter. This means the load is NOT on the bolts to maintain the power, rather into he casing of the bell housing; Yes the bolts are doing some work there, but with both shafts locked in zero worries.  End of the day, the Mazworks solution is the easiest and safest. no need to take your trans to a shop to get milled perfectly, it fits with minimal clearancing, and you can use all your existing clutch and flywheel.  Driving wise the CD has been great compared to the big box, I'll probably swap my final drive at some point. The serial 9 shifter is gooooood, my only qualm is how tight it is, it takes a fair bit to get use to, 5th and 6th are a bit eh/hard to find at times, but maybe I need re-adjusting, and I think my clutch master is very tired and needs a rebuild. 
    • If you are keen, have a look at my build thread. Car is for sale for the right money or straight swap for a F80 M3 LCI.
    • Welcome mate.  No point in over thinking it, buying any one of those cars you mentioned is not a smart or logical choice with the availability of many "better" (re price to performance) cars available to you.  The heart wants what the heart wants, buy whatever it leads you too.
    • Hey everyone! Im so grateful to be apart of this community and ill do my best to be apart of this. Firstly, i'm not disclosing my real name due to in real life circumstances surrounding my privacy and public image (sorry lol) Secondly, The only thing personal I am willing to share is that I'm from Sydney and a descendant of one of Sydneys largest mortgage firms. I got gifted my first ever car, a 2022 Porsche Cayenne and I love it to death. Ive been driving it for about 5 or 6 months now and honestly Im so grateful for my parents for gifting me this vehicle. However recently I've been working my ass off to afford my second car (which I need help deciding soooooo community help me out please?). Once decided, im planning to try modify it myself. Recent I've been thinking about getting a Skyline, particularly a 25GT or GT-V, yes I know overrated as hell, but I'm also considering a Chaser which I recently came to love. However my dream is to one day own a 180SX (So hard to find clean versions and im not really into importing).  Lastly before I send this off, I want to apologize if I sound tacky or pretentious. I try not to and want to genuinely learn from everyone and anyone. (Im no expert in this area) Thanks for reading!
×
×
  • Create New...