Jump to content
SAU Community

Stock Bov Plumb Back Into Intake

abu

By abu,
in Engines & Forced Induction

 Share

Recommended Posts

abu Grand Master

abu

Posted
Posted

Hey

I have changed the setup on my R32 RB20DET and am no longer able to use the stock intake pipe and plumb back system

Long story short I am using a 3" metal intake pipe with has provision for the rocker cover breather (hooked up with no issues) and to plumb back a blow off valve

I am using the stock cross pipe with the stock RB20 BOV and want to plumb it back into the intake pipe but my problem is I am having problem finding a hose (flexible to run from the BOV outlet to the intake pipe

I am no longer using that huge plumb back metal pipe junk, as it doesn't fit with the new setup

I have been to Autobarn, REPCO and Clark Rubber but can't find a hose in the right diameter - just wondering what everyone else has done and how I can get around this

I had one other idea which was to use an adapter to reduce the outlet size on the BOV - so use that stock hose with a fitting that reduces the outlet size so I can use a smaller hose to the intake pipe

But will this be restrictive or cause any issues?

Any help would be appreciated

:P

Link to comment
https://www.sau.com.au/forums/topic/213794-stock-bov-plumb-back-into-intake/
Share on other sites
TTT Grand Master

TTT

Posted
Posted (edited)

Can you make something out of metal (what ever material you used for your intake pipe) that sits in between the stock bov return hose (just the rubber hose that used to join your bov to the metal return line) and the small rubber joiner you wil luse at the intake return point?

example in words..

Bov outlet===rubber joiner===new metal return line bent to the shape you need===rubber joiner===intake pipe bov return hole.

essentially, fabricate a new metal return pipe to replace the factory metal bendy return pipe.

I have also seen people use this sort of shit..

http://www.morriscoupling.com/Products_Ind...od13_14_pic.jpg

Obviously they come in all sorts of ID sizes.

Have a look in Clarks rubber.

they might have something for you.

the above stuff does not kink.

I've also seen it used for connections of catch cans.

Perhaps Bunnings or other plumbing stores might be able to help too

Edited by GTST
abu Grand Master

abu

Posted
  • Author
Posted

I thought about making something out of metal but would prefer just to use normal hose as its easier and looks more stock

I managed to find some hose but it was slightly smaller and just managed to squeeze into the stock hose on the BOV outlet - would something like that be ok?

Would diameter make a difference and is there a lot of pressure in that plumb back hose?

I saw that flexi shit at Clark Rubber but the diameter just falls short of what is needed and I don't know how good that would be - I reckon it would melt pretty quick or go all hard and brittle.

It's similar to loom tube which eventually breaks and cracks away

Bunnings was useless - I had a look around and couldn't find anything so I showed one of the guys there the size of hose I needed and he goes, 'go to autoban'

Thanks for the ideas

TTT Grand Master

TTT

Posted
Posted

unless you start to hear flutter, then it's fine.

If you start to get flutter, then there is some sort of restriction in the Venting.. either the bov or the return line.

if the return line hasn't been reduced too much in diameter, then it shouldn't be a problem till you are well up in the 300rwkw as per Mafia's car.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GoHashiriya
      R34 Skyline Sunroof Won't Tilt/Vent

      By GoHashiriya · Posted

      Actually, that's not entirely true. It's also the same motor in the 1st gen Nissan Cube but they're rare as hen's teeth.  
    • Duncan
      Unknown sound similar to BOV on positive boost with partial throttle RB26

      By Duncan · Posted

      Yeah it is always worth testing and balancing actuators out of the box, just set the pressure regulator on a compressor very low (eg 5 psi) and increase it slowly to see when they both move.....unfortunately while you may be able to adjust the length of the actuator rod to minimise any difference, the actual pressure they move from is not adjustable so you need a well matched pair. And yes, the VCAM is probably contributing; the earlier in the rev range they come on boost and the slower the revs build (I think your demo was in 5th), the more you notice it.  Driving at WOT through 1st, 2nd, 3rd etc you will probably never hear it as any shuffling starts and is over super quickly
    • Dose Pipe Sutututu
      Shoota's R33 GT-R RB30/26

      By Dose Pipe Sutututu · Posted

      oh they were with that motor, you need to remove the engine to change the spark plugs (don't have to, but it does make it easier)
    • nouveau_poor
      Unknown sound similar to BOV on positive boost with partial throttle RB26

      By nouveau_poor · Posted

      I certainly fall into the annoyed camp, but glad to hear that if it's happening at low boost then I'm not likely going to blow a turbo and end up with metal shards in my oil. Just feels like it prevents me from really driving it without hesitation and "peak" performance. Wonder if it's the VCAM, it did an impressive job of shifting the torque curve and faster spool, but maybe now it's "too fast" and there's too much air for how open the throttle is.  Based on some other threads, will also do some reading on synchronizing the actuators. They are the default actuators that come on the Garrett's and I would think they would be set the same coming from the factory, but if the turbos don't actually work exactly the same way at the same time as previously mentioned, it would be worth making sure the actuators are actuating together properly
    • GoHashiriya
      R34 Skyline Sunroof Won't Tilt/Vent

      By GoHashiriya · Posted

      I went down this rabbit hole before, ended up sourcing a motor from the UK (I'm in Japan) which also didn't function correctly. With the original motor, I disassembled it and reassembled it and it works somewhat, sometimes. What I could deduce from all my screwing around is that there is calibration of the gears on the inside of the motor and two ramps on the main gear which activate switches that operate the motor and move the sunroof either to retract into the roof or tilt. Where I got stuck was that, it seemed in my case that one or both of the switches that are activated by the ramp on the gear did not always activate and thus the motor did not move, causing it to sometimes not retract or tilt (apologies, I've forgotten which way it didn't work.).  Of course this part is discontinued at Nissan now, it's the same part in the S15 but no other models. I also contacted the manufacturer of the component for schematics - forgot the name, they're based in Gifu - but they declined to share the information due to being bound by an NDA, sadly. Looking through my pictures now, it seems I last had a crack at this in 2022. See, I so kindly wrote "open" and "close" next to the switches. If you figure it out, please do tell me. Those little switches, with the red buttons may need to be replaced.
×
×
  • Create New...