Jump to content
SAU Community

Fs- Rb20det Engine (spun A Big End)

kretch
 Share

Recommended Posts

kretch Contributor

kretch

Posted
Posted (edited)

Item: Nissan RB20det

Age: not sure

Condition: spun a big end, had done bout 90000kms

Price: $400 ono

To Fit: (What car) whatever u choose

Location: Northern beachs ,Sydney

Contact: 0417986654 or PM me

Comments: Gday i got my old rb20 out of my cefiro for sale, it has spun a big end, i tryed putting new bearings in it but it still knocked. Will need crank reground, or get a 2nd hand crank and will be all good. Comes less engine wiring loom, AC compressor. Pretty much everything else is there. I have a series 2 RB25det turbo/actuator and dump (77000km NO shaft play) i can throw for $400, it will bolt straight up.

I also have 4 sale-

Series 2 RB25det turbo (77000km NO shaft play) straight bolt up for rb20det aswell

RB20det ECU

RB25det sump

rb25det AC compressor

RB20det oil relocator

Make me some offers

Prob some more stuff il have a look when i get home.

Edited by kretch
Link to comment
https://www.sau.com.au/forums/topic/214435-fs-rb20det-engine-spun-a-big-end/
Share on other sites
kretch Contributor

kretch

Posted
  • Author
Posted (edited)

*i also have a tubular exhaust manifold to go with the turbo, has a crack in it but easily fixed.

*Ive got a Apexi AFC the one with the knobs- $150 ONO

*RB25det engine mount brackets and bolts (the silver bits, not rubber mounts) open to offers

*RB20det air flow meter, good con $80

*Stock intercooler piping for 1997 Nissan Stagea. open to offers

Edited by kretch

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      New kid on the block

      By GTSBoy · Posted

      The wiring diagram for the R33 RB25 is freely available, and is essentially the same same as most other RBs (just with differences as to which pin # does which job). To get the ECU to power up, you just need to provide power to the ECCS relay, and have the other power feeds that come in from the top left of the wiring diagram (wrt the ECU) that give perma power to the fuel pump relay, the ECU itself, etc etc, all connected. When you put power on all these it will just come to life. It's pretty clear from the diagram what needs to happen. Just follow the lines from the 12V + supply stuff in the top left over towards the ECU. I've even posted snips of such diagrams (not for vanilla 25, I think for Neo and 26) to various threads here in the last few months, talking about what it takes to get the fuel pump and FPCM up and going. Search these up and they will help get you started on doing the same with the vanilla 25 diagram. Hell, for all I know, I've done the same with that one in years past and have forgotten.
    • Duncan
      New kid on the block

      By Duncan · Posted

      Yep...so unless someone posts up the answer you will need to probe from the ECU connector to the dash plug with a multi meter in continuity mode to trace the wires.  Note the ECU has multiple - and + (and across different key settings - Battery, IGN and Start) and most likely the power is fed from the connector(s) that is normally near the left hand headlight.
    • Songo
      New kid on the block

      By Songo · Posted

      Thanks Duncan, I am actually just trying to get the Rb turning and running with the RB25DET S2 original loom itself  I am just trying to get it going outside the body and not thinking about the S15 or trying to match anything to the S15 loom at all I am only trying to see if anyone has done this and what pin they found to be the ignition trigger and ECU+/- on the dash connector, that's about it. Thanks  
    • iain_ST44GA
      M35 VQ25DET starter motor

      By iain_ST44GA · Posted

      Hi Guys, Does anyone know any aftermarket part numbers for a starter motor to suit the VQ25DET? I can find lots of alternative part number for the VQ35DE, which I assume would fit, but there is a lot of conflicting information out there. Thanks..
    • Murray_Calavera
      R33 GTR running -9 with no tune

      By Murray_Calavera · Posted

      I don't understand how this hasn't boiled down to - Upgrade the turbo when you have everything required. ECU, injectors, fuel pump, turbo, etc. Do it all at once.  If you don't have everything required, just enjoy the car as it is and keep saving up your pennies. 
×
×
  • Create New...