Jump to content
SAU Community

Fs - 6 X 440cc S15 Injectors And Gtr Fuel Pump

SexyPete
 Share

Recommended Posts

SexyPete Collaborator

SexyPete

Posted
Posted (edited)

Item: 6 x 440cc S15 Injectors

Age: As old as an S15

Condition: Great

Price: $350 delivered anywhere in Aus

To Fit: Direct replacement for the R33 gtst and capable of 250rwkw + a bit more with a FPR

Location: South Sydney (Sutherland Shire)

Contact: PM if interested

Comments: Selling as they are not large enough for my new master plan, picture only of 1 but I have 6 identical

Item: GTR fuel pump on bracket bolt in with strainer and plug

Age: As old as a GTR not sure which model possibly R33

Condition: Good

Price: $80 delivered anywhere in Aus

To Fit: Direct replacement for the R33 gtst and capable of 250rwkw perfect match with S15 injectors

Location: South Sydney (Sutherland Shire)

Contact: PM if interested

Comments: Selling due to not enough flow for my new master plan

This is a perfect combination for a high flow turbo setup. Will sell both together for $420 delivered. These are both direct bolt in replacements no mucking around needed. Pick up welcome also Sutherland shire.

post-32096-1208042057_thumb.jpg

post-32096-1208042099_thumb.jpg

Edited by SexyPete
SevenAngryPenguins Proficient

SevenAngryPenguins

Posted
Posted (edited)

I had mine flow tested at 3 bar just last week and they flowed 500cc and doesn't the skyline run 43psi rail pressure so id say 480 is spot on and of the of 6 injectors 4 were jdm and 2 were adm i.e. they are the same as already said^^

Edited by SevenAngryPenguins

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • The Bogan
      NC MX5

      By The Bogan · Posted

      Kittens in first to claim dominance of the residence, then puppies later From past experience, the other way around can be problematic to say the least  Those weird "Dobby looking"  little kittens are not cheap....LOL
    • MBS206
      NC MX5

      By MBS206 · Posted

      At least yours have parkour down pat. One of mine will still trip over his own shadow and fall over... He's a special type of cat... Ha ha ha
    • MBS206
      NC MX5

      By MBS206 · Posted

    • SteveL
      Leak from Tokico BM50 Brake Master Cylinder

      By SteveL · Posted

      The question then becomes - was there any fluid coming from that hole before you did the rebuild ?    You may not have noticed, of course.   Depending on how you did the rebuild, the possibility has to be considered that somehow (cleaning ?)  fluid entered that hole and is now being 'forced'  out by small movements of the proportioning valve.   From the factory, there's actually a small rubber plug in that hole but with age and under-bonnet heat it's quite common for it to 'go missing'.  That rubber plug is designed to allow the venting process but also to prevent 'stuff' getting to the area (prevent corrosion, etc).   The plug is also not available as a spare part AFAIA. Personally I wouldn't race and buy a new master just yet but keep an eye on the area to see if the 'leak' continues.   If you're concerned about brake fluid damaging nearby paintwork, cable tie a piece of suitable absorbant material over the hole and remove/monitor occasionally.    Operation of the proportioning valve and the brake master itself won't be affected, but also keep an eye on brake fluid level, of course. In terms of a new master, the genuine part is getting expensive, unfortunately.  Amayama is showing AUD900+.   I was searching recently and there's an aftermarket part available from Japan made by 'Parts Assist': https://zenmarket.jp/en/yahoo.aspx?q=BNR32%2bBM50&p=1 Whether it's any good I have no idea, although in my experience Japanese aftermarket stuff is pretty good quality-wise.   The above site allows overseas buyers to purchase stuff more easily from Japan but there are fees and shipping costs, of course.   The original Japanese seller page is here: https://auctions.yahoo.co.jp/jp/auction/p1197401228 Copper/Nickel is fine but I still prefer bundy tube and it's also cheaper.
    • Duncan
      NC MX5

      By Duncan · Posted

      Your chihuahuas look weird!
×
×
  • Create New...