Jump to content
SAU Community

Recommended Posts

I am posting on behalf of a friend of mine who is trying to sell the following:

Camshafts: JUN blanks NEW (actually huge 292* with 11.35mm lift ) very big , therefore are considered as blanks which can be grind back to any spec you want. - SOLD

HKS valve springs - SOLD

Call Jack on 0402 751143

[email protected]

Link to comment
https://www.sau.com.au/forums/topic/21502-jun-camshafts-and-hks-valvesprings/
Share on other sites

288 degrees duration, 11.35mm lift??!?! These are JUN's biggest camshafts eek.gif

Holy hell, they're some SERIOUS camshafts :( You'd better be aiming for about 900hp to consider these!!!

Also, regrinding them is ridiculous, you'd be losing JUN's huge amount of R&D into matching lobe seperation, intake and exhaust durations and exacting lift measurements, and making them all work in tandem... That's what you're paying for in these magnificent camshafts!! Not the metal composition...

I just wish I had a GTR that these camshafts would suit, because this is an awesome price...

Menios is interested very very much .. have u still got them ,, merli im not considering 900 , but around 650 ... that is a gr8 price,, although dont u lose the case hardening if u regring??? maybe im wrong but isnt that an important facxtor,,,. SICK itll souind like a v8 lol lump lump lump lump REV!!!!!!!!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Oil change does not trigger code 21. Code 21 is for coilpacks primary side connection. You can try to clear the code with a battery disconnect, hold down the brake pedal to drain capacitors through the brake lights with the ignition on for 10-15 seconds before you reconnect the battery. I have seen R35 coil conversion permanently cause this code with no ill effects so it might be the resistance it wants to see isn't quite right on one or more coilpacks. Could be inside the ECU, could be the harness, could be a coil. You can test it all if you want or just ignore until the car actually starts misfiring.
    • I forgot you have a Nistune ECU. Use Nistune to do all the tests I mentioned instead of faffing with 30+ year old electrical connectors. You can read MAF volts off that too, there are reference values in the service manual to tell you roughly what it should be in different conditions.
    • No. I think it might be the AFM. Hence the use of the terms "swaptronics", which implies the use of swapping out electronics for the purpose of diagnosis. It's about the only way to prove that a small/niggling/whatever problem with an AFM or a CAS or similar is actually caused by that AFM/CAS/whatever. A known good item swapped in that still gives the same problem is likely to be caused somewhere else. They're all the same. Spraying AFMs with cleaner is an each way bet between cleaning it and f**king it.
    • Oh wow! This might actually work amazingly. Do you know the ratio of the diff? I was told the only thing you need to make sure of is if the front & rear diff ratios are the same. Ours is a 4.083 Thanks!
    • You think its the AFM? I know its a common issues on R32s. I find it coincidental how this issue raised right after cleaning the fuel system. As everything except the fuel system was fine before. I tried running it with the IACV unplugged but did not notice a difference and still stalled. However, the RPM gauge is not in the cluster right now, so I will need to connect the laptop again and use Nistune to check the RPM. I will check this weekend.
×
×
  • Create New...