Jump to content
SAU Community

Recommended Posts

Hi all just wanted some opinions....

Tonight i installed a HKS SSQV in my rx7 and the piece of shit doesn't work. I welded on the flange to the pipe, put the o-ring in the flange, put the bov over it and put in the cir clip. T-Pieced the vacuum line off the FPR. Thought sweet no worries... Took it for a drive and low and behold massive turbo flutter just like before. Thought no worries ive stuffed something, probably vacuum, pulled off the vacuum line to the bov and could feel/hear the suction. I thought It was probably stuck shut form living on my shelf for three months. Pulled it all off, put a screw driver in and pushed the second stage all the way open, then put another screw driver in and pushed the 1st stage open as well. Thought to myself yep i think it was stuck because i herd that cracking noise when a seal hasn't opened in a while.

Put it all back together took it for another drive on 6psi, no bov sound all flutter, changed to 14psi same again.

Got the shits, picked up my ball and bat and went home

that and the sun went down

So my questions are:

how do i bench test the ssqv?

does it need to see vacuum like a normal bov or does it magically just need positive pressure for the reference?

how the bloody hell does it work? i cant work out how it could ever overcome the pipe pressure to open?

Thanks Acea

Edited by 84ace
Link to comment
https://www.sau.com.au/forums/topic/215822-hks-ssqv-broken-fixed/
Share on other sites

Hi all just wanted some opinions....

T-Pieced the vacuum line off the FPR.

biggest mistake i see a lot of people do because they are too lazy to find a real vacuum line.

Do people know that this is dangerous, and since your adding crap to this mission critical line, it might leak \ come apart and lean the engine, and possibly kill it at high revs?

I've even seen someone dumb enough to run a line from the front of the engine off the FPR line, over the top of the engine down onto the turbo boost controller... Hot engine, rubber hose.. attached to a FPR line.

If I were you, I'd plump that line to a better spot to start with anyway.

biggest mistake i see a lot of people do because they are too lazy to find a real vacuum line.

Do people know that this is dangerous, and since your adding crap to this mission critical line, it might leak \ come apart and lean the engine, and possibly kill it at high revs?

with my set up i have two choices, i can t-piece the FPR and boost gauge line, which i did or i can t-piece the microtech map sensor line. I think i chose the right one, considering how critical the microtech is to the "mission," anyway... its pretty easy to see when the boost gauge continuously reads 0 instead of reading plus or minus half a brick. I think i would pick up a problem with that line pretty quickly.

So that leaves me with another option, drill and tap a new fitting into the manifold. No.

so back to it... either there inst enough volume of air getting to the bov or its broked....

with my set up i have two choices, i can t-piece the FPR and boost gauge line, which i did or i can t-piece the microtech map sensor line. I think i chose the right one, considering how critical the microtech is to the "mission," anyway... its pretty easy to see when the boost gauge continuously reads 0 instead of reading plus or minus half a brick. I think i would pick up a problem with that line pretty quickly.

So that leaves me with another option, drill and tap a new fitting into the manifold. No.

so back to it... either there inst enough volume of air getting to the bov or its broked....

you have more choices

what ever happened to the original BOV line? did it magically disappear?

There is one for the factory boost guage

THere is another back there just sitting around doing nothing

there are more free if you choose to remove your carbon canister.

Map sensor, and FPR pressure, are definately mission critical lines, so stay away from them. You do realise a f**kup on that line and a sudden drop of fuel pressure could blow your engine? Also, the BOV could cause fluctuations on the FPR pressure, making it go all over the place? I can't confirm that, but its definately a possibility..

Couldnt agree more. In 5 years of working with dynos ive seen 3 cars blow motors over vacuum hoses blowing off. Both had dodgy BOV plumbing, two on the FPR, the other on the MAP sensor. When you are at full throttle on the dyno, it takes about 0.1 seconds for the motor to blow.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...