Jump to content
SAU Community

Recommended Posts

Make sure you buy one thats been serviced at a mazda dealer that way you know everything has been done on time.. and if you can buy one still with some warranty.

The major services are every 40,000kms and the are upwards of $450 but all the other services should be below $280 so long as you dont have any extras needed.

They are a good car though.. and i'm not just saying so because i work for Mazda :thumbsup:

Link to comment
https://www.sau.com.au/forums/topic/216714-mazda/#findComment-3828246
Share on other sites

get the mazda 3, i work for them and we barely have any probs with them. we get sum that come in and they say they get around 600 - 700ks per tank of fuel. the best ive heard is 1000ks per tank.

I can vouch for that. Very nice car. The Mazda 3 Maxx Sport never gets under 600k out of a tank, typically I get more than 660k per fill. They drive with mercedes like handling, and have enough power in the 2.0L petrol variant for driving to make it satisfying to drive without planting the accelerator. And most impressive of all they are quiet, and stay quiet after a few years too!

The car is very handy with the roof racks on full time, still very quiet, and tow bar too.

The ONLY SINGLE fault and enough to make me rant about it that I can make of this vehicle is the air conditioning,

which I have been told needs to be changed to a custom aftermarket solution for the condensor panel to make it blow hard and cold.

It is cold enough to maintain a comfortable temperature just not strong enough to do something like bring it down to sub 20 degrees celcius on a 38 degrees celcius day.

A typical summer day like that and it will sit at a constant 23-26 degrees on the freeway regardless of the a/c fan speed setting.

I need an air conditioner to go to at below 20 degrees no matter how hot it is outside. This is because after exercising running around and run back to the car, I feel sweaty and need to cool down to get rid of the humid feeling.

I guess this car was made for Japan with the expectation that you will park your car in an undercover car park during the day at the office, not for active Australians, who have to leave their car in the sun, and who after doing so and driving for 2 hours will expect to eventually cool down in the car, which will never happen in this car.

Link to comment
https://www.sau.com.au/forums/topic/216714-mazda/#findComment-3828319
Share on other sites

Mazda 3 is a nice car,

was almost going to buy one... then on the drive to the mazda dealership I spotted a sleek looking car on the corner of a car yard, turned out to be this quirky thing called an r33 skyline.

ended up buying the skyline (talk about a completely different world) and started my love affair with imports, was never a big fan of cars before then. Go figure

Link to comment
https://www.sau.com.au/forums/topic/216714-mazda/#findComment-3828942
Share on other sites

lol I was going to buy the mazda 3 as well, never ever heard of a skyline b4 that

but whilst browsing on the net, I found this awesome looking silver s2 skyline

went for a test drive and all that practicality shit went straight out the window :D

Link to comment
https://www.sau.com.au/forums/topic/216714-mazda/#findComment-3829753
Share on other sites

lol I was going to buy the mazda 3 as well, never ever heard of a skyline b4 that

but whilst browsing on the net, I found this awesome looking silver s2 skyline

went for a test drive and all that practicality shit went straight out the window :down:

Well I just sold my Skyline after two years of ownership and really need to find a cheap to run but nice and reliable car (looking to spend between $16-$23K)

Im also buying a house soon so hence why I cant really afford to keep a fuel hungry PULP drinking car.

Link to comment
https://www.sau.com.au/forums/topic/216714-mazda/#findComment-3830763
Share on other sites

I can vouch for that. Very nice car. The Mazda 3 Maxx Sport never gets under 600k out of a tank, typically I get more than 660k per fill. They drive with mercedes like handling, and have enough power in the 2.0L petrol variant for driving to make it satisfying to drive without planting the accelerator. And most impressive of all they are quiet, and stay quiet after a few years too!

The car is very handy with the roof racks on full time, still very quiet, and tow bar too.

The ONLY SINGLE fault and enough to make me rant about it that I can make of this vehicle is the air conditioning,

which I have been told needs to be changed to a custom aftermarket solution for the condensor panel to make it blow hard and cold.

It is cold enough to maintain a comfortable temperature just not strong enough to do something like bring it down to sub 20 degrees celcius on a 38 degrees celcius day.

A typical summer day like that and it will sit at a constant 23-26 degrees on the freeway regardless of the a/c fan speed setting.

I need an air conditioner to go to at below 20 degrees no matter how hot it is outside. This is because after exercising running around and run back to the car, I feel sweaty and need to cool down to get rid of the humid feeling.

I guess this car was made for Japan with the expectation that you will park your car in an undercover car park during the day at the office, not for active Australians, who have to leave their car in the sun, and who after doing so and driving for 2 hours will expect to eventually cool down in the car, which will never happen in this car.

yeahthey will get that all the time. we always get people that ask about the a/c with them but the way 2 get them realy cold is have them set on recurculate instead of fresh. we have tested 1 car that on a 34 degree day we had the ac sitting around 7degrees.

Link to comment
https://www.sau.com.au/forums/topic/216714-mazda/#findComment-3833912
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • our good friends at nismo make a diff for it, I have one (and a spare housing to put the centre in) on the way. https://www.nismo.co.jp/products/web_catalogue/lsd/mechanical_lsd_v37.html AMS also make a helical one, but I prefer mechanical for track use in 2wd (I do run a quaife in the front, but not rear of the R32)
    • What are we supposed to be seeing in the photo of the steering angle sensor? The outer housing doesn't turn, right? All the action is on the inside. The real test here is whether or not your car has had the steering put back together by a butcher. When the steering is centred (and we're not caring about the wheel too much here, we're talking about the front wheels, parallel, facing front) then you should have an absolutely even number of turns from centre to left lock and centre to right lock. If there is any difference at all then perhaps the thing has been put back together wrongly, either the steering wheel put on one spline (or more!) off, and the alignment bodged to straighteb the wheel, or the opposite where something silly was done underneath and the wheel put back on crooked to compensate. Nut there isn't actually much evidence that you have such a problem anyway. It is something you can easily measure and test for to find out though. My money is still on the HICAS CU not driving the PS solenoid with the proper PWM signal required to lighten the load at lower speed. If it were me, I would be putting either a multimeter or oscilloscope onto the solenoid terminals and taking it for a drive, looking for the voltage to change. The PWM signal is 0v, 12V, 0V, 12v with ...obviously...modulated pulse width. You should see that as an average voltage somewhere between 0V and 12V, and it should vary with speed. An handheld oscilloscope would be the better tool for this, because they are definitely good enough but there's no telling if any cheap shit multimeter that people have lying around are good enough. You can also directly interfere with the solenoid. If you wire up a little voltage divider with variable resistor on it, and hook the PS solenoid direct to 12V through that, you can manually adjust the voltage to the solenoid and you should be able to make it go ligheter and heavier. If you cannot, then the problem is either the solenoid itself dead, or your description of the steering being "tight" (which I have just been assuming you mean "heavy") could be that you have a mechanical problem in the steering and there is heaps of resistance to movement.
    • Little update  I have shimmed the solenoid on the rack today following Keep it Reets video on YouTube. However my steering is still tight. I have this showing on Nisscan, my steering angle sensor was the closest to 0 degrees (I could get it to 0 degrees by small little tweaks, but the angle was way off centre? I can't figure this out for the life of me. I get no faults through Nisscan. 
    • The BES920 is like the Toyota Camrys of coffee machines. E61 group head is cool, however the time requirements for home use makes it less desirable. The Toyota Camry coffee machine runs twin boilers and also PID temp control, some say it produces coffees as good as an E61 group head machine.
    • And yes with a full tank it will hit limiter free revving or driving 6B6CDF6E-4094-426D-A9CB-6C553475FE36.mp4
×
×
  • Create New...