Jump to content
SAU Community

Recommended Posts

Hi all,

Just wondering if neone could tell me what this is or what they think it is. Basically i can only here it at idle and very low in the rev range as its not that loud just irratating (Spelling). Its coming from the engine bay and sounds to me like a leaking exaust manifold but it did it before i got my extractors and now it still does it with the new ones and new gasket, i changed the oil and its still there? someone once told me that its normal for Double Over Head Cam engines to do this but i disagree, the car still runs fine and isnt lacking in power its just really starting to annoy me.

Ne Help Much Appreciated.

Cheers

John

Link to comment
https://www.sau.com.au/forums/topic/21687-ticking-sound/
Share on other sites

In my old 202 it was the hydraulic lifters, and my GTS-T makes this same sound. I was told cheap oils can make your car do this, but I have been running fully synthetic in mine, so Im not too sure whats going on. Anyways, It never hurt my 202 and my 33 is going strong.

Link to comment
https://www.sau.com.au/forums/topic/21687-ticking-sound/#findComment-461315
Share on other sites

  • 2 weeks later...

could be hydaulic lifters.

I have been told that Mazda's have a bad problem with this, and they have a special oil additive to fix it.

Put it in with the oil run for 20mins until noise is gone, then drain oil. Apparently it (oil) comes out black, thick and lumpy. Basically the additive is an internal engine cleaner.

Ask your friendly Mazda dealer about some

Link to comment
https://www.sau.com.au/forums/topic/21687-ticking-sound/#findComment-492424
Share on other sites

"yeah i always get bad fumes in the cabin if sitting in traffic for a while. gives me a saw throat after extended preiods, im assuming its not real good for you."

N/A_R33,

mate you have an exhaust leak, go to an exhaust specialist and have it checked out...they will find where it is...

i had the same problem with a previous car, after changing the exhaust manifold gasket many times and not fixing the problem, i discovered that the manifold face was warped and not sealing properly...

had the manifold machined and problem fixed!

Cheers

Link to comment
https://www.sau.com.au/forums/topic/21687-ticking-sound/#findComment-492624
Share on other sites

i had it checkd and it seems one of the 'rear' bolts for the exhaust manifold is missing, sposedly this is a common problem in 33 gtsts and 95% of the time people dont bother replacing them as its a huge job, i can definitely hear the clicking of the air leaking but as far as power/econoy nothing seems to be affected, two different tuning shops told e not to worry about it unless it starts to get worse, any suggestions ? anyone know how much it usually costs to get the bolt fixed ?

Link to comment
https://www.sau.com.au/forums/topic/21687-ticking-sound/#findComment-492731
Share on other sites

I got mine engine tap tap tap last month when cold start, noise gone when warm.

On way back from GOR cruise, my car misfiring ratatatata hard on 3rd gear acceleration. The next morning oil pressure running low, car has flat spot everywhere but that cold start tap tap tap noise totally gone....... what the?????????

Car is slowly getting better and better to drive, but still a bit flat spot and won't make boost on 1st gear (gauge only goes to 0). Now boost only comes in 2nd gear or higher (gauge goes to a bit over the halfway mark between 0 & +7).

On cold start, oil pressure will go past 6 mark on +/-1200rpm idle. When warm, on 700rpm idle oil pressure is a little less than 2. When driving around 2500-3000rpm oil pressure is about 4, and cruising 4th gear 60kph about 2000-2500rpm the oil pressure drops to about 3 or 3.5 mark.

Strange..... very strange......

Link to comment
https://www.sau.com.au/forums/topic/21687-ticking-sound/#findComment-494048
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Working through possible solutions of converting my mechanical speedo.    Anyone know what type of speedo sensor the factory r34 gtr getrag has ? what the output is ? I assume its not a VSS and more a voltage like earlier speedo sensors ? Can an ECU read it ?  
    • roof rail delete used to be a thing, they were made locally for a while too
    • I can get more photos of it here soon and I plan to make a thread detailing the process. I received the car this way and it sorely needs refinishing. That is probably the most appealing photo of it. Up close it is fading, cracked, and needs to be re-glued. Depending on their condition I'm on the fence between refinishing or making a new set.  Another angle hiding the pimples and razor pumps  
    • According to this thread the RS4V with build plate RC40 comes with the R200 diff @ 4.083 ratio as well (mine has said RC40 denotation). We may need to check if the axle stubs are the same pattern as well. The auto subframes have longer axles. However I think yours being a later Series 2 as well, we should have the same bolt pattern for the diff stubs. Unless your upgraded rear also has upgraded axles. Either way, I would not be opposed to pulling the covers to check so I can inspect that  fancy rear core  Also I don't have HICAS. I don't believe that should change things but I hope the people here with heaps more experience than me can correct me if I'm wrong   Let me know if you want to attempt to make this work and I can get some pictures of mine from under the car. 
    • It's not that straightforward. For example I have had this code because my ignitor/power transistor wires were unplugged. It knows something is wrong but has no idea what it means. If you want to actually diagnose this I recommend following the service manual flowchart for code 21. Ohm out the harness, coilpacks, inspect the ECU, etc. And again, it's entirely possible for there to be no problem at all but if you're running a different coilpack it'll trigger the code because it doesn't like what it sees.
×
×
  • Create New...