Jump to content
SAU Community

Recommended Posts

Neesan r33 gtst
5 spd
vg30 TURBO
front mount
Big zaust, mines dump to high flow cat and 3.5 inch to cannon. (Very deep RB rumble)
155000kms
New shocks and springs.
hicas lock bar
R33 GTR wheels, New rubber on front. the white 18's are no longer on the car
Full rego
Stereo with sub ect. Old stereo.
Two stage boost controller. 10 and 7 psi.

new Rear wheel bearings, new water pump.

Everything works.


Car is white with sunroof.

Only setback with the car is the dash surrounds have been painted white, and switch surrounds.
running 10psi

[number removed at OP's request] for info.



post-21954-1210572808_thumb.jpg
post-21954-1210573805.jpg
post-21954-1210660293_thumb.jpg

Hi champ,

Would you be willing to trade for a 1993 R33 GTS-T. 103k kms. Black, auto with a few simple yet tasteful mods..

Let me know.

Kind Regards,

more pics, all around and interior...

interested...

More pics are in the pipe line.

Looks much better with the R33GTR Rims if you ask me.

Not much interest?

It is cheap and is in excellent condition, I had it washed at lunch time and with the paint only being a year old it looks fantastic!

Car has factory Skyline mats front and rear, no tears or holes in any seats.

The car drives great, gear changes are smooth, clutch is perfect (not very old)

Perfect start for a cheap Skyline that looks the goods.

Neesan r33 gtst
5 spd
vg30 TURBO
front mount
Big zaust, mines dump to high flow cat and 3.5 inch to cannon. (Very deep RB rumble)
155000kms
New shocks and springs.
hicas lock bar
R33 GTR wheels, New rubber on front. the white 18's are no longer on the car
Full rego
Stereo with sub ect. Old stereo.
Two stage boost controller. 10 and 7 psi.

new Rear wheel bearings, new water pump.

Everything works.


Car is white with sunroof.

Only setback with the car is the dash surrounds have been painted white, and switch surrounds.
running 10psi

[number removed at OP's request] for info.



post-21954-1210572808_thumb.jpg
post-21954-1210573805.jpg
post-21954-1210660293_thumb.jpg



Hey Mate,

Selling it so soon? whats the deal? and why so cheap?

I am keen for sure. You have Pm

I have seen this car in the flesh and it is pretty shmick, great for the price I say!!
I think you should lower the price, there is a Series 2 on here for 9 with only 100gs on the clock.

http://www.skylinesaustralia.com/forums/19...er-t218690.html

hmmmm cant really compare those hey - not a fair nor nice comment

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • How do you propose I cable tie this: To something securely? Is it really just a case of finding a couple of holes and ziptying it there so it never goes flying or starts dangling around, more or less? Then run a 1/8 BSP Female to [hose adapter of choice?/AN?] and then the opposing fitting at the bush-into-oil-block end? being the hose-into-realistically likely a 1/8 BSP male) Is this going to provide any real benefit over using a stainless/steel 1/4 to 1/8 BSP reducing bush?
    • I fashioned a ramp out of a couple of pieces of 140x35 lumber, to get the bumper up slightly, and then one of these is what I use
    • I wouldn't worry about dissimilar metal corrosion, should you just buy/make a steel replacement. There will be thread tape and sealant compound between the metals. The few little spots where they touch each other will be deep inside the joint, unable to get wet. And the alloy block is much much larger than a small steel fitting, so there is plenty of "sacrificial" capacity there. Any bush you put in there will be dissimilar anyway. Either steel or brass. Maybe stainless. All of them are different to the other parts in the chain. But what I said above still applies.
    • You are all good then, I didn't realise the port was in a part you can (have!) remove. Just pull the broken part out, clean it and the threads should be fine. Yes, the whole point about remote mounting is it takes almost all of the vibration out via the flexible hose. You just need a convenient chassis point and a cable tie or 3.
    • ..this is the current state of that port. I appreciate the info help (and the link to the Earls thing @Duncan). Though going by that it seems like 1/4 then BSP'ing it and using a bush may work. I don't know where I'd be remote mounting the pressure sender... to... exactly. I assume the idea here is that any vibration is taken up by the semiflexible/flexible hose itself instead of it leveraging against the block directly. I want to believe a stronger, steel bush/adapter would work, but I don't know if that is engineeringly sound or just wishful thinking given the stupendous implications of a leak/failure in this spot. What are the real world risks of dissimilar metals here? It's a 6061 Aluminum block, and I'm talking brass or steel or SS adapters/things.
×
×
  • Create New...