Jump to content
SAU Community

Recommended Posts

Hey guys,

Im in the process of choosing a body kit i have chosen two and shown it to a couple of people and some are saying

"yeah sexy" other "no way"

i just need some outsider views to what i should do

33gtrfront2.jpg ad390.jpg

Edited by Bombshell
Link to comment
https://www.sau.com.au/forums/topic/217452-help-me-decide/
Share on other sites

  • Replies 73
  • Created
  • Last Reply

Top Posters In This Topic

Most people (me included) aren't fans of the veilside kit, so don't expect too many nice replies :D

Ive been told to get a GTR kti but not being a GTR might look to try hardish lol :ban: . Ive been looking for kits everywhere but stil cant seem to find one that really takes my fancy ar there any sites you could show me with a variety on it??

Edited by Bombshell
Link to comment
https://www.sau.com.au/forums/topic/217452-help-me-decide/#findComment-3839195
Share on other sites

Best thing for R33's and skylines in general is to keep it simple as far as body mods, A lot of aftermarket kits ruin the factory lines by being too chunky or have way too much overhang (ala veilside's creases and folds), R34's especially look horrid with most aftermarket kits (I do like the top secret one though)

As much as people will bag the 400r front bar for being too common, it's that way for a reason, prolly the best looking bar getting around aside from a gtr style bar.

When I had my R33 I had 400r sideskirts and a cutom rear lip on the bumper to match. I was going to put on a gtr style bumoer but ended up selling it and getting my R34

This is a pic of a genuine 400r, there are many fibreglass copies available. Similar styling to this would be my pick, aggressive but understated, not over the top like veilside

post-29425-1209744044_thumb.jpg

Edited by Yo-Yo
Link to comment
https://www.sau.com.au/forums/topic/217452-help-me-decide/#findComment-3839678
Share on other sites

I personally hate the veilside kit... looks like a Darth Vader on steroids... ugly and just doesn't flow with the R33's lines (like another member said above)... GTR kit is fine as long as with no badge... the TRUST or TOP SECRET front bar is fine.

Link to comment
https://www.sau.com.au/forums/topic/217452-help-me-decide/#findComment-3839733
Share on other sites

how the hell is 400r understated? serious question

Agreed. However, the 400R 's front bar looks too crowded... too much vents and stuff, i.e. I hate that vent thing on the side... personally, the GTR kit is king of the pack. Simple but tough.

Link to comment
https://www.sau.com.au/forums/topic/217452-help-me-decide/#findComment-3839735
Share on other sites

i personally disliked 400r kits before i had a r33.

but i find the 400r kit looks alot better in person then it does in picture!!

the car i ended purchasing had a 400r front bar and i fell in love when i saw it ><

Thanks

So where would i be able to find a 400r kit from? Are there any sites which u could recomend.

Link to comment
https://www.sau.com.au/forums/topic/217452-help-me-decide/#findComment-3839785
Share on other sites

what kit do you have on your car at the moment?

i personally thing the stock type m front bar and the gtr bars look the best

i have a 400r front bar which is good as well

oh and i have excreted feces that look better than the veilside kits

I havnt got any kit on my car at the moment just stock 33, thats why i wanna try make the right choice. I have looked at a fair few kits but nothing is really taking my eye.

Link to comment
https://www.sau.com.au/forums/topic/217452-help-me-decide/#findComment-3839990
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
    • Pull codes via the self-diagnosis procedure. As far as I can tell this is just a sign of transmission issues but not a code unto itself.
    • Hi All, putting the engine back together and everything is perfect except have this plug left over.. any ideas what it is for and where it goes? Is on cold side under the intake plenum *note not a stock plug, as everything has been modified Cheers
×
×
  • Create New...