Jump to content
SAU Community

Turbo Problem And Question!

boliztik
 Share

Recommended Posts

boliztik Enthusiast

boliztik

Posted
Posted

hey,i have a 32 gtst with an rb25, every time i slow down from boost i get white smoke that puffs out from the exhaust (fair bit)

none on idle or anything only slowing down. from what i know its probly a blown oil seal on the turbo... correct? if so whats a rough price for new seals with labour?

engine specs: standard rb25 turbo running 10 psi, 3 inch no cat, microtec, ebc, 040 fuely etc

also i have a brand new garrett t04 sitting around, would it be better to fit this? i have boch 040 fuel pump but standurd injectors, once again would like a rough price from ur experiance.

sorry to ramble on...

cheers dylan

Link to comment
https://www.sau.com.au/forums/topic/217573-turbo-problem-and-question/
Share on other sites
The Dan Grand Master

The Dan

Posted
Posted

Don't discount valve stem seals. You need to perform tests to determine which is the cause of your problem.

Remove the turbo and manifold and do a vacuum test on the exhaust ports to determine the condition of the valve stem seals. If they come up ok, then you need to examine the turbo.

I'm not about to go into depth into how you should do this as you won't even have the tools or equipment to test the valve stem seals anyway.

Good luck

The Dan Grand Master

The Dan

Posted
Posted

sorry mate, it's a harsh reality. Valve stem seals are more likely to leak at negative cylinder pressure as the vacuum effect draws oil through the stem seals. They can weap at idle also but it slowly gets burnt away and not so noticable. On decel, the cylinder draws oil past the stem seal and because you have no real combustion until you resume accel, it will become quite noticeable at this point.

Could still be your turbo but would hate to see you replace it and have the same problem without checking it properly first.

tridentt150v Grand Master

tridentt150v

Posted
Posted

3lit3 is correct, but decel will vacuum suck oil in from a few places, even up past the oil control rings in the bore [although rings usually also smoke after an idle period then accel].

I think you need to determine if the white smoke is oil or water/coolant as well, this could help you determine where to look.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MissMintyR33
      R33 persistent issues. P/steering and lag/misfire

      By MissMintyR33 · Posted

      I thought that might be the case, thats what I'll start saving for. Thanks for the info 
    • jtha7
      Strange issue RB25DET wont start

      By jtha7 · Posted

      Ps i found the below forum and it seems to be the same scenario Im dealing with. Going to check my ECU coolant temp wire tomorrow    From NICOclub forum: s1 RB25det flooding at start up Thu Apr 11, 2013 7:23 am I am completely lost on this. Car ran perfectly fine when I parked it at the end of the year. I took the engine out and painted the engine bay, and put a fuel cell with an inline walbro 255 instead of the in tank unit I had last year. After reinstalling everything, the engine floods when the fuel pump primes. if i pull the fuel pump fuse it'll start, and as soon as I put the fuse back in it starts running ridiculously rich. I checked the tps voltage, and its fine. Cleaned the maf as it had some dust from sitting on a shelf all winter, fuel pressure is correct while running, but wont fire until there is less than 5psi in the lines. The fuel lines are run correctly. I have found a few threads with the same problem but no actual explanation of what fixed it, the threads just ended. Any help would be appreciated. Rb25det s1 walbro255 fuel pump nismo fpr holset hx35 turbo fmic 3" exhaust freddy intake manifold q45tb q45 maf   Re: s1 RB25det flooding at start up Fri Apr 12, 2013 5:07 am No, I didn't. I found the problem though. There was a break in one of the ecu coolant temp sensor wires. Once it was repaired it fired right up with no problems. I would have never thought a non working coolant temp sensor would have caused such an issue.
    • jtha7
      Strange issue RB25DET wont start

      By jtha7 · Posted

      Hi sorry late reply I didnt get a chance to take any pics (my mechanics on the other side of the city) but the plugs were fouled from being too rich. I noticed the MAF wasn't genuine, so I replaced it with a genuine green label unit. I also swapped in a different ignitor, but the issue remains. I've narrowed it down a bit now: - If I unplug and reconnect the fuel lines and install fresh spark plugs, the car starts right up and runs perfectly. Took it around the block with no issues - As soon as I shut it off and try to restart, it won't start again - Fuel pressure while cranking is steady around 40 psi, injectors have good spray, return line is clear, and the FPR vacuum is working. It just seems like it's getting flooded after the first start I unplugged coolant sensors to see if its related to ECU flooding but that didnt make a difference. Im thinking its related to this because this issue only started happening after fixing coolant leaks and replacing the bottom part of the stock manifolds coolant pipe. My mechanic took off the inlet to get to get to do these repairs. My mechanics actually just an old mate who's retired now so ill be taking it to a different mechanic who i know has exp with RBs to see if they find anything. If you have any ideas please send em lll give it a try. Ive tried other things like swapping the injectors, fuel rail, different fuel pressure regs, different ignitor, spark plugs, comp test and MAF but the same issue persists.
    • GTSBoy
      Freddy Plenum vs Genuine options RB25

      By GTSBoy · Posted

      My return flow is custom and puts the return behind the reo, instead of at the bottom. All my core is in the air flow, rather than losing some of it up behind the reo. I realise that the core really acts more as a spiky heatsink than as a constant rate heat exchanger, and that therefore size is important.... but mine fits everything I needed and wanted without having to cut anything, and that's worth something too. And there won't be a hot patch of core up behind the reo after every hit, releasing heat back into the intake air.
    • Murray_Calavera
      R33 persistent issues. P/steering and lag/misfire

      By Murray_Calavera · Posted

      There is a really fun solution to this problem, buy a Haltech (or ECU of your choice) and put the MAF in the bin.  I'm assuming your going to want more power in future, so you'll need to get the ECU at some stage. I'd put the new MAF money towards the new ECU. 
×
×
  • Create New...