Jump to content
SAU Community

Recommended Posts

Hey guys, looking for some opinions!

Got an AE86 sprinter, currntly with a CA18DET conversion!

Now with the issue, the car has actually gone through 4 CA18's due to a number of things, but the last engine just blew up after being run a 7,000 rpm in 5th gear for a fairly long period of time! It burnt out the rod bushes on cylinder 4, basically screwing the bottom end!!

Just measuring up some options that we have now, which are to work the current CA18 giving it forged pistons, rods and a new crank rod, allong with boring out the oil wells to try and allow the oil to run to the bottom of the engine faster which we have been advised could have caused this issue! Also adding a larger and baffled oil sump! oh this engine is running a VL turbo pump with microtech computer and soarer FMIC running stock boost!

APPROX. $3500

The other option is to actually replace the current engine with a stock SR20DET and a small amount of boost! obviously having to change the engine mounts and exhaust pipe and using the standard computer! can get half cuts to do this for the usual $3000 to $4000!!!

What do you guys think would be a better option for reliability sake as this car does do track etc!! it runs great on stock CA18DET but the reliability doesn't seem to be any good!!

but heard that the SR20's have some generic faults as well!

which one would be a better option!

All sugestions would be great!

Link to comment
https://www.sau.com.au/forums/topic/21835-sr20det-vs-ca18det/
Share on other sites

You thought of actually reducing the rev limiter down to a more reasonable 5000rpm and tuning the car more for peak power at around there, to reduce the stresses on the engine?? Just a thought...

Especially if you are doing heaps of drift work, peak power isn't everything.

With the SR20DET it also builds torque a fair bit lower down in the revs, so that would probably suit your application more it sounds. Don't forget the CA18 is pretty old now.. whereas the SR20DET still has pretty good support in terms of bolt-ons from Japan.

A proper rebuild on the CA will give you a fresh engine with forgies and rods for about 4000 or so if you remove the engine and take it to Roccos Performance. Theres a bokethere who loves CAs

An engine/gearbox swap to a SR from an S13 will cost you 4000 minimum (front cut) and it's still an unknown quantity. Plus you have to do the swap and engineer it and dick around fabricating new mounts and pipes so It'll blow out to 4500-5000 easy.

I'd go the CA rebuild unless you canget a SR engine that has a known historyon the cheap. It's easier and you will have a stronger engine at the end of it.

Just my opinion.

The CA will probably rev better for longer.

The sr wont like bouncing off the rev limiter or sitting at 7k rpm.

The valve train in the sr has been skimped on compared to the CA. Unless u switch the GTiR pulsar lifters etc.

Have a read of http//:members.iinet.net.au/~sayer/biscuits/

or search for silvia australia, and read the tech articles on the pro's an cons of both.

Originally posted by GaryD

the other thing to think of too is the sr20 is a fair bit lighter. could suit the 86 a bit better? but if i was in your position id rebuild the ca

Actually the engines weights are very similar.

Externally, The 2 engines look completely different, and they should. The first obvious difference is the SR’s shiny alloy block, Next you notice the different inlet manifolds. The list goes on. Don’t mistake that alloy bloke as being lightweight either – there is that much alloy in the thing to keep it strong that they weigh no less than the CA.

This was taken from Nissan Silvia SR vs CA

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • 21 is explicitly the coils detected as the issue. Is it guaranteed the actual issue? No. Just the ECU thinks it is. When you say rattling, describe it better, get an audio clip as best you can if possible.
    • Yea got me coppers. Bad news is I just put them in and the car still has the light and shakes. I also noticed I hear like rattling coming from the exhaust piping right under me. Does 21 also have a possibility of being O2 sensors?   So, coil packs are good, the harness is good, the MAF is working, and obviously the spark plugs just replaced and working.
    • Make sure you drop the GTT base tune back in, and set your injectors again, this will remove anything playing up with it you may have removed. Possibly lean there as it's normally a fast transient going THROUGH atmospheric pressure, and a turbo motor would then quickly go richer as boost builds. The only worry you MIGHT have is ignition timing, as the DE is higher compression than the DET from memory. But again, you're not in boost, so the DE motor will be a lot more forgiving at atmospheric.   Get Murray, Kinkstahs, and Johnny's input on tuning haltechs, those guys have played with tuning enough in the past to be able to help now you're past the trouble shooting stage of the MAP issue
    • @Rusty NutshI mate. Do you have a pinout diagram for the na neo auto ecu? 
    • Yeah thats the plan now. 🤞
×
×
  • Create New...