Jump to content
SAU Community

Recommended Posts

Mine used to do this too. It would just randomly blink quicker than normal, as if a globe has blown, but once you take a turn, it would return to normal. I too have a 32 sedan.

I think it's been a loose connection or a faulty globe though.

I normally get this issue after blowing an indicator globe. However (once) I needed a new universal timer thing that controls the indicator timing, I can't remember the real part name....except that it was about $15 and bought from Bursons or Autobarn.

  • 3 months later...
  • 4 weeks later...

Hi, hope I don't cause bad bumpage of this thread, though I felt it was better to have it in the same spot than start a new one.

This morning my indicators started doing the same thing, just on the left side.

I haven't had the chance to check it out thoroughly yet as I just got to work, but it's only the front left on the front bar that isn't working.

If I put hazard lights on, they all blink at the usual rate, but still not the front bar left indicator.

Is this a normal thing to happen when an indicator globe goes? Or could I expect it to be something else? It's only happened this morning..was kinda scary in traffic when you can only see the reflection of one indicator and not knowing if people know your intentions with turning =S

Also for the OP. Your car being a sedan doesn't mean your car shouldnt have side indicators. As far as I know its actually something that is meant to be done at compliance to comply with Australian standards.

I gather this isnt harshly controlled as their is a lot of imports missing them. But saying that, I have seen plenty of sedans with them.

Have you checked you have side intrusion bars lol?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi all. Been a while but things are moving along. I just have something that I am wondering about. Since I will use OEM turbo oil pumbing, I got myself a new bolt, the one that goes into the engine block oil feed. As I recall (and see visually) this bolt comes restricted with I think a 1.7mm hole? Not quite sure but it was something around that size. The turbos have 1mm restrictor bolts installed, as necessary due to ball bearings and my higher oil pressures. Can I now just use that OEM bolt with the 1.7mm hole in for the engine block or will this actually be too much oil flow restriction and I have to drill it out first? In my head it would make sense for the bolt to be at least 2mm wide as both turbos take "1mm of oil flow". Do let me know if my logic is flawed here, I just want to make sure I don't kill my turbo bearings with too little oil. Don't know if I can trust the saying I read somewhere that ball bearing turbos essentially only need an oil mist
    • There are several aftermarket options available, from not-too-painful moneyhttps://justjap.com/collections/driveshafts-bearings/products/d-max-reinforced-replacement-rear-driveshaft-set-fits-nissan-s13-s14-s15-r32-r33-r34-c35 and  https://justjap.com/products/crank-motorsport-billet-rear-axles-fits-nissan-skyline-r33-gts-t-r34-gt-t?srsltid=AfmBOorQk4xkGUa98kO7v2ePLUiNt-HRrM2AwWNw9mbSIVE1ujBVwY__, all the way up to The Driveshaft Shop https://driveshaftshop.com/skyline-cv-axles/
    • Yeah based on old XRC5964S specs, it looks to be roughly GTX3576R sized? But this 5964S compressor will flow 90lb airflow somewhat similar to the compressors in both the GTX3584RS or G35-1050.. I fully expected the 0.64 rear A/R to choke up top - seems way too small from typical convention - but these are seemingly beneficial over the prior 0.82 results.. Be interesting to see if he comments on the EFR question in that thread - he mentioned in a prior video that BW EFR's were the "cats pajamas 10 years ago", but by the sounds of things all his kits have been using Xona for quite a while now.
    • Yeah it’s still got the oem manual gearbox and clutch, only kinda mods are a blow off valve, coil overs, and a aftermarket intercooler. Also had it for about 2 months now with a lovely midnight purple paint on it.
    • Yeeeppp, been following a lot of the testing on the latest Xona stuff and there are some mental results.  He also went over 1000hp @ 4 hubs on his Mainline with a XRE6364S (63mm) which was also well into the 20psi range before 4000rpm on a 2.5. Crazy stuff. Fwiw the XRE5964S is basically the modern equivalent of their old HTA3582 - would drive nicely enough on an RB25 or 26, but proven capable of a huge amount of power if you want to spicy with rpm tho even at sane boost levels will make stout numbers 
×
×
  • Create New...