Jump to content
SAU Community

Oxygen Sensors Rb25 To 26

skylinekid
 Share

Recommended Posts

skylinekid Proficient

skylinekid

Posted
Posted

hey everyone im currently puttin a rb26 into a gtst and im using the 25 harness.... is basically the same except for knock sensor plugs.... in regard to using one single 02 sensor im unsure if i could use the rb25 sensor and it will compute properly with the 26 computer.... unsure if they are the same band width as such.

thye different i see is the plug and the wires are different coulours 25= white red black 26= white white black apart from that does neone know if it would work thnx

and yes im aware i will have to splice wires since im running single turbo setup..

Link to comment
https://www.sau.com.au/forums/topic/218504-oxygen-sensors-rb25-to-26/
Share on other sites
paulr33 Grand Master

paulr33

Posted
Posted

different 02 sensors (type) and wiring

depending on what ECU you use, if you use an rb25 ECU, youll need to use a single rb25 02 sensor

or you can just leave it out and have no 02 feedback, the car should still work and run fine (just crap fuel economy)

R31Nismoid Grand Master

R31Nismoid

Posted
Posted

Dont even bother.

Just turn them off via the Hand Controller, no need for them anyway.

I ran mine without for years, no problem.

I've only got a set in there now for the EPA so it doesnt flash a fault light via ECU codes/consult etc.

skylinekid Proficient

skylinekid

Posted
  • Author
Posted (edited)

but just for shits and giggle i want the 02 sensor in there and functionable neways..... i have been doing sum reasearch and according to a couple of ppl the gtr sensor when the car is started the internal heater is on until car is hot then heater is turned off.... gtst sensor heater is constantly on also i have been told sum of the gtr sensor came with 4 wires not 3.... so yeh got me stumped for the minute lol

and as i said earlier i would just bridge the 2 inputs so i can get a reading for both and just even it out but yeh im aware thats its not needed for tuning with power fc.

the main thing i need to know is if i can or cant use the 25 sensor to a 26 computer thats my only issue

Edited by skylinekid
skylinekid Proficient

skylinekid

Posted
  • Author
Posted

on closer inspection i have noticed that the 2 sensors for rb26 have to different plugs hence to not cofuse fron turbo with rear turbo sensors id say. the good thing is the 2nd sensor has the same connector as the rb25 so it will just be plug and play. but i will double check its functioning and not just hope it is lol. thnx for all the help guys much appreciated.

skylinekid Proficient

skylinekid

Posted
  • Author
Posted
Still a bit confused by the problem, if you have 2 o2 sensors, why dont you just use them both, and wire it up the way it is from the factory

bcuz 1 sensor for one turbo ya dont need 2 plus i dont wanna have to run more wiring capeesch

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • RP1421
      S15 Spec R

      By RP1421 · Posted

      As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • joshuaho96
      R32 GTS (RB20DE) Injectors Replacement

      By joshuaho96 · Posted

      I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
    • perry_r33
      R34 GTR Vspec Garage Sale - All must go!

      By perry_r33 · Posted

      Pm sent 
    • Robot
      Skyline v36 350GT sedan hunting on idle

      By Robot · Posted

      Hi,  Just joined the forum so I could share my "fix" of this problem. Might be of use to someone. Had the same hunting at idle issue on my V36 with VQ35HR engine after swapping the engine because the original one got overheated.  While changing the engine I made the mistake of cleaning the throttle bodies and tried all the tricks i could find to do a throttle relearn with no luck. Gave in and took it to a shop and they couldn't sort it. Then took it to my local Nissan dealership and they couldn't get it to idle properly. They said I'd need to replace the throttle bodies and the ecu probably costing more than the car is worth. So I had the idea of replacing the carbon I cleaned out with a thin layer of super glue and it's back to normal idle now. Bit rough but saved the car from the wreckers 🤣
    • GabsReDeal
      R32 GTS (RB20DE) Injectors Replacement

      By GabsReDeal · Posted

      After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
×
×
  • Create New...