Jump to content
SAU Community

Recommended Posts

Originally posted by GTS-t VSPEC

Brett, Good idea, I'm sending forms to various people, and will start collecting them, but yes the dyno day on Sunday October 5th would be ideal for a final decision etc.

Shit Paul,

I have already faxed off the form that you gave me yesterday. Of course no payment was issued with that form so do you want to collect that money of the Dyno Day.

:uh-huh:

  • Replies 504
  • Created
  • Last Reply

Top Posters In This Topic

Originally posted by EVL R33

Paul,  Fuel Pump, new Z32 afm's, pods,   'hi flo cat', then tuning with the cam gears and 700cc injectors that are already in it to around 1.4 bar..

Anybody want a standard GTR fuel pump???

Can always use another pump, me please. How much you speak Joe........:)

I wish I was in a position to give stuff away free, but unfortunately I have to charge to offset the cost of the new pump. PM me so we don't whore this thread and we'll talk. I advertised it in the for sale for $300 ono but will take less than that, one guy has offered $200 over east, I'd rather deal local as COD sh*ts me no end...

Cheers

Brett

Paul, maybe we can talk to Lloyd and tell him we will have the forms to him on the 6th... Otherwise we can collect them over the next week or so from everyone.

BTW. Brendan won't be putting his car into PAS so we have to look elsewhere. Maybe the guy that bought Ken's car will let us put it in???

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • So, now all you need to do is connect the 2 or 3x 12v feeds into the unit to permanent 12v, ACC 12V and IGN 12V that you can find in the spot behind the stereo, and the earth, and then it will switch on with the car.
    • Yes then it will turn on but I want the car features to work  
    • My thought is if you were just moving it forward and the upstream geometry remained the same, then no difference at all. But because the current one has the filter direct into the AFM inlet, you effectively have the best chance of a completely symmetric air flow profile upstream, and in, the AFM, whilst the aftermarket inlet thingo has a (small, to be sure) bend between the filter and the AFM. That would bias the flow to the outside of the bend (downstream of the bend) which might well reduce the size of the signal seen by the AFM, for the same total flow rate. Having said that: If you're proposing to make your inlet look like a hybrid of your existing one and the aftermarket one, such that there is no bend where the filter is clamped on... then I say it will be just fine. If there is going to be such a bend, then, if you can align the insertion of the AFM blade such that it is at right angles to the plane of the bend, then there is a better than even chance that the centreline velocity where the blade is will remain more or less the same, and the velocity will just be a little faster to the outside of that, and just a little slower to the inside. **This is not professional investment advice and you should consult a suitably qualified ouija board, tea leaves or the intestines of a goat for more accurate prognostication.
    • Hi Tao, Thanks for your reply.  It's been a while and I managed to get the valve stem seals replaced with the head on the car.  Unfortunately this didn't solve my issue, the car still smokes a lot after idling (to be honest during idle you can see a bit of blue smoke from the exhaust), same after deceleration. I will try disconnecting the valve cover breathers, do I leave the PCV valve in? By engine oil drain pipe, do you mean the turbo oil drain?
    • What about if you just give it direct 12v and earth?
×
×
  • Create New...