Jump to content
SAU Community

Recommended Posts

When The AP Engineering PFC was plentiful and could be imported for around 1k a ramp was worth ~800 for the first tune and then approx 500-600 for further tunes.

The PFC on the other hand was ~1k + ~300 for tunes. So I went with the PFC.

Speak to Jeff at Turbo Tune and see what he does remaps for. The only option these days is to drop a rb26 pfc in to the r32 gtst. It does have additional benifits of inlet air temp sensor correction etc which is handy for those hot days or thrashing it at Mallala.

what cubes said.

oif u can get a PFC cheap as chips.. .then do it, buit personally the remap is the way to go, and dont be folled into thinking that the PFC is better then the Stock ecu as this often is not the case, One example is the stock ECU has detonation control, where as the PFC flashes a light at you.

depends on what power your wanting and what your going to be using the car for...

if its dailey driven and just want abit of a tune then the remap is alot cheaper option then a new computer system for a 32 plus its not defectable.

with the extra cash you save on for a remap you can use to buy some mods for the remap.

Simon the std ecu does have det control but it is very limited.

R32's and RB25's have still cracked ring lands due to det on the stock ecu. :)

Personally I prefer the dash light flashing as you then know something is wrong and can get it rectified.

ImportS13... A remap is defectable but is not 'detectable'. Either is the pfc if you shove the stock ecu's cover on it. :(

nothing is idiot proof... if your thrashing on a 40 degree day with shit fuel, the thing is going to ping to death with even the smartest ecu on board. that said, i like the fact the stock ECU will do SOMETHING rather then NOTHING. a flashing light is well and good but when im on the track i dont look at the dash :(

Agree nothing is idiot proof. If the knock map is tuned conservatively no doubt you will feel the power be sucked out of the car so probably a little better than a flashing light. The other concern would be if its too conservative egt's will skyrocket if you keep stuck in to it.

The rb26 pfc ecu has inlet air temp correction, 20x20 fuel/ign maps (finer tune) vs 16x16 on the std ecu.. another couple of plus but for an additional price. :(

If I could get the ecu remapped for $500-600 and then further tunes for a few hundred I'd jump at it.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • I put another 2 layers of putty and still getting pinholes. Think i might either try the filler first then putty or just leave the little specs of guidecoat as is and get primer to fill it in. I think i misread understood what you said above when you said my glazing putty wasnt enough for the size of the area. I thought you meant 1 coat and i needed to. But i think what you meant was that I needed filler first? I also went a bit too far out the repair area as my spreader is a bit large.
    • You do sorta. In my instance they were little specs and I didn't even think they'd be pin holes but it all makes sense now. Huge learnings there!
    • Ah ok that makes sense and it's where i think i went wrong because before when i put filler then putty, i didn't have this issue and now i do because i only put 1 coat of putty. Thanks for that heaps man, it's a good way to put it! With my putty I'm using the dolphin glaze which i just saw it says finishing putty lol. I didnt put filler cause it was a shallow area but i see what you're saying. Also I'm an idiot, i just realised that while i put new putty there are pinholes! I probably saw it before and ignored it for whatever reason. I think because i thought putty is used to fill pin holes that itself wont make pinholes but that's incorrect of course. I feel silly now haha. ok I think I know what to do next. Thanks man!
    • Yes correct, the guide coat is showing low spots, in this instance the low spots are pin holes. I agree wetting the areas makes it more visible (but you can see it's there before you wet it as well lol).  Once the panel is flat, the guide coat will be gone  
    • I wouldn't do it outside, the contamination landing in the paint, the wind and a million other things will drive you crazy.     That's a way too big of an area to use your single stage putty on.  Pretend it's all filler and those pin holes appeared, you'd then use the putty on those pin holes.  They are still pin holes, hmm I expect a few coats of high fill primer could deal with those. 
×
×
  • Create New...