Jump to content
SAU Community

Fs: Vic: Gt3540, Wastegate, High Mount Manifold, 2 Rb25 Heads

VIP_R31
 Share

Recommended Posts

VIP_R31 Apprentice

VIP_R31

Posted
Posted

Item: Virtually brand new Garrett GT3540, has spooled maybe twice, .63 rear housing,

Age: two weeks

Condition: brand new

Price: $1600, can come with heat wrapped dump for $150extra

To Fit: whatever you like

Location: SE melbourne

Contact: 0407 741 599, PM, Mark

Comments: the reason I am selling all of this gear is because, it was on a 25, paid heaps for this whole setup to get done, first dyno run blew the botom end of the 25, bought a second hand 25 and on startup the bottom end was blown, so I'm over it now.

here are two pics of the turbo

engbay.jpg

03042008379.jpg

Item: brand new High mount manifold to suit RB25, stainless steel, with heat shield for RB25

Age: two weeks

Condition: brand new

Price: $350,

To Fit: RB25DET

Location: SE melbourne

Contact: 0407 741 599, PM, Mark

Item: brand new Tial 44mm wastegate (silver) 10psi spring, can come with screamer for $40extra

Age: two weeks

Condition: brand new

Price: $650, can come with screamer for $40 extra

To Fit: anything you like

Location: SE melbourne

Contact: 0407 741 599, PM, Mark

Item: 2 x RB25 heads take what you need, can take whole motor for same price (both have blown bottom ends)

Age: both are S2 motors

Condition: good heads, broken bottom ends

Price: $350 each

To Fit: Rb25DET, or 30DET,

Location: these will be in the northern suburbs

Contact: 0407 741 599, PM, Mark

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • klutched
      GOT SUM's RB34

      By klutched · Posted

      Got some decent progress after work yesterday and also today. Got the ECU all wired and passenger side interior all back together. Kept the wiring up nice and high to avoid people standing on it. Got the surge tank relays rewired and tidied up the pump wiring and cut a hole to bring the cables through.  I found a spare USB cable I had lying around so I decided to cut it up and see if I could use it for my CAN 1 bus. Turned out one of the pins I needed was to the shield of the cable so i cut it up and desoldered it and resoldered to the correct pins.  Had the issue with the powersteering hose hitting the A/C compressor and fan shroud. I pulled the bracket off and modified it to remove the front mounting point which now clears it all. Will keep an eye on it to see if theres any signs of fouling once it's up and running.
    • hardsteppa
      R32 OEM rims name?

      By hardsteppa · Posted

      That's some good input mate. Nice.
    • PranK
      My BMW 335i

      By PranK · Posted

      So today I went well outside my comfort zone (again) to replace my valve cover gasket.  I have had a big leak over the exhaust leading to a lot of smoke and smell every time I drove it. The leak was in the rear driver's corner.  The job wasn't hard as such, just a bit finicky and time consuming.  The old gasket was rock hard and broken right where the leak was.  The leaky corner had so much sitting oil in it.  The good news to my amateur eyes was no buildup or sludge under the cover. It all looked fairly nice in there.   I haven't started it yet. I ran out of light and body when putting the coils and injector loom back in. Probs only 30min left for the morning.  I was so nervous putting the cover back on, I must have lifted it 5 times to make sure the gasket was still seated properly. God it's going to be nice to be leak free and not make other traffic light queuers think my car is about to explode.
    • The Bogan
      MLR's Bogan cruise ship

      By The Bogan · Posted

      Gave the Mazda it's first wash, it will need some clay, a light compound, and polish polish to remove a few swirl marks, but that will be a job for when I have a full day to get my DA polisher action on
    • Jonesy93
      R32 vs R33 R34 C34 heater core matrix and elbow pipes info thread

      By Jonesy93 · Posted

      Just did this job on my 32 with the boost doc kit. was quite simple to fit, hardest part was getting the rubber bungs back on the firewall. does anyone know how the heater will work now without the flap in the bend? Will I just have a heater on 24/7 now?
×
×
  • Create New...