Jump to content
SAU Community

Recommended Posts

Holden, HSV,VX Clubsport, series2 2001 mdl, 5.7 ltr gen3, 6spd manual, 129,000km, full service history. The car is silver in coulour verry verry clean inside and out and mecanicly A1, the only mods are a short shifter, a 3" twin cat exhaust. It also has a $4000 stereo in it that has only had around 4hrs use, JVC DVD head unit, JL splits, pioneer kevlar coned 6x9s (the yellow ones), two Kicker comp VR daul voice coil subs, alpine 1000watt digital mono block, alpine 4 chanel amp, stinger wireing and accesories. The car hasnt been thrashed but it go's hard, standard it has 255kw and with the exhaust and extractors adding another 10 or 15 kw it would have about 270kw. The clutch is also aftermarket but still driveable on the street.

I will trade it for a 32, 33 ,34 GTR or highly modded GTST or GTT, also interested in s13's, s14's, s15's, evo's supra's and wrx's etc etc. I have a few V8's but I want another import to play with. can also do cash adjustment either way.

myclubbby.jpg

clubby.jpg

clubbyint.jpg

PM me or reply in the thread with your offers and ill get strait back to you :ermm:

Edited by WHITE R33
if u were in nsw i might of

yeah that sucks because your car looks nice as if its the one in the avatar!!!!!!!!!!!!!! ahh well cheers anyways mate

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • ok so if i wanted to go 18's i would go for 8's  in front 30+ or 32+ off set at front and the back 9 would be ok? what offset should i aim for.. then can i do some  hunting for wheel rim choices..    If i get this - will this fit all around: Size: 18 x 8.5 +37 - n what tyres size tyre should i get for front n back?  
    • Absolute f*cking nightmare. I had to take breaks constantly, and I was always pissed off when I got home. The line split in Italy on day 2 (we drove from the Netherlands), lol. Driving any narrow European town was... well, sh*t.   Appreciate it man. Here, I'll just drop a favourite from the load I took on Saturday.   I'll update here when things happen with the car, the thing is, with stock power and almost everything chassis-wise taken care of, there really are no problems. 268,000kms now and counting.  
    • Ah! I actually managed to snag a lightly used set.... that aren't so suitable for me right now. They don't work on a GTT without some cutting or creative heat moulding. I thought about reselling them myself cause I didn't want to murder them, but it looks like I'm probably going to attempt to murder them/melt them because I may as well. @GTSBoy @PranK can somebody close this thread?
    • Hey mate,  I have a set, one is slightly damaged but wont be noticable once installed.  Shoot me a message if your still after them 
    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
×
×
  • Create New...