Jump to content
SAU Community

1989 R32 Gtr

STR8E180
 Share

Recommended Posts

STR8E180 Proficient

STR8E180

Posted
Posted (edited)

Make: R32 GTR

Model: 1989

Milage: 61 XXX

Transmission: Manual

Colour: gray

Location: NSW

Complied? YES

Currently registered? YES

Price: $28 000

Contact: PM

i no longer want to keep my GTR

i dont have enuff room for it and i dont have enuff time to enjoy it so im better of selling it

car is very well maintained ive spent alot of money on replacing parts which didnt need to be replaced just to keep it well maintained

Engine

HKS step1 camshafts 264/264

HKS adjustable camgears

HKS inlet manifold gasket

Gates timing belt

custom stainless heat treated billet CNC machined oil pump

R33 RB26 crank shaft

external oil return lines from cylinder head to sump

Garrett GT35R Ball Bearing turbo

TiAL 44mm external wastegate

screamer pipe

custom steampipe Manifold

custom dump pipe + front pipe

hi flow 3inch cat

X force cat back exhaust system

115mm intercooler

custom aluminum intercooler piping

custom intake pipe

custom air box

greddy blow of valve

custom catch can

aluminum radiator

Fuel System

SARD fuel reg

SARD 800cc injectors

Bosch 023 fuel pump

Management

Power FC D jetro

Power FC commander

Suspension and Brakes

cusco coil overs with swift springs

hicas lock bar

EndLess VN front pads

EndLess brake fluid

DriveTrain

HKS triple plate clutch

HKS fly wheel

Interior

Recaro SR3 Passenger & Driver side

Blitz ID3 boost controller

Gizzmo shift light

Defi-Style 3 Gauge Din Dash

Defi style boost gauge

Greddy remote control boost switch

Exterior

CR KAI 18 X 9.5 +12 BRONZE

Nismo side skirts and Nismo rear pods <----- not fitted yet

6000k HiD headlight kit

POWER: 316kw @ 16psi

lastscan2.jpg

Maintenance

2x cam seal

1x drive shaft seal

2x nissan cv boot kits

5.5L Penrite HPR40 40

1x endless VN front pads

0.5L endless brake fluid 50

1x reverse gear lock-out selector

2x earl's -6 adaptor

2x blanking cap

2x 16mm copper washer

2.5L mobil delvac synthetic diff oil

1x nissan water pump

1x nissan oil pump gasket

1x nissan front crank seal

2x earl's -12 weld-on fittings

1m earl's -12 braided line

2x nissan exhaust manifold gasket

DSC_0023.jpg

DSCF0855.jpg

DSCF0858.jpg

Edited by STR8E180
Link to comment
https://www.sau.com.au/forums/topic/221973-1989-r32-gtr/
Share on other sites
STR8E180 Proficient

STR8E180

Posted
  • Author
Posted (edited)
standard internals?

every thing listed is every thing done

standard piston's and rods if thats wat ur asking for

internal upgrades are basic the bottom has

R33 RB26 crank shaft

billet cnc machined oil pump

brand new bottom end bearings

pretty much just freshened up the bottom end just for that extra piece of mind

the cylinder head has

hks step 1 cam shafts 264/264

hks adjustable cam gears

gates timing belt

all new geniune nissan oil seals

Edited by STR8E180
Link to comment
https://www.sau.com.au/forums/topic/221973-1989-r32-gtr/#findComment-3927722
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Haggerty
      RB25DE NEO with Haltech ECU

      By Haggerty · Posted

      Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • brillo
      Leak from Tokico BM50 Brake Master Cylinder

      By brillo · Posted

      Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • MBS206
      Cas issue

      By MBS206 · Posted

      It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • nash47
      Cas issue

      By nash47 · Posted

      Yes sir am asking is there possible way from aem tuner from wiring pins 
    • MBS206
      Cas issue

      By MBS206 · Posted

      Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...