Jump to content
SAU Community

Recommended Posts

Item: Work Meister 20x10.5 only one in Australia

Age: Used lest then 5-6 months old

Condition: Still good condition, just a minor few stone chip on it but u cant be able to notice it.

Price: $6000

To Fit: GTR 34

Location: Perth

Contact: 0424444439

Comments: The tire still got more then 95% percent trade because i hard used them. Is 275/30/20 :)

Edited by Hoshima
Link to comment
https://www.sau.com.au/forums/topic/223477-fs-work-meister-s1-2p-20x105/
Share on other sites

  • 2 weeks later...
  • 4 weeks later...

Updated, now i got 2 set of wheels. Got another set is Time Attack TE37 19x10.5 brand new in the box come with tire 275/30/19, anyone who interested can pm. I will only let go for the right price, as i order this wheels from japan took me 7 months to get hold with it.

The offset of the TE 37 TimeAttack wheels is +22. Will fit nicely on GTR 34. As for the Work Meister, i will included the postage for that price ;)

  • 4 weeks later...

More pic added with ztuned fender and stock fender, time to get rid of it any offer i may consider aslong is not stupid offer, thanks. Pm me if ya serious about it, no time waster!!

CIMG1711-1.jpg

CIMG2018.jpg

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
    • I'm a fan of the JZX110, and the Aristo. Big cruiser cars, and with the factory cars, super comfortable and feel like you're driving an armchair! And the JZ motors are a pretty nice engine too, especially with some basic mods.   The import process, and the need to be able to trust people, and the fact there's so many scammers around is what ever puts me off wanting to go through that ordeal!
    • I don't care for these at all, but at least the underside looks straight and not rusty. A good basis for a long life. Many cars from Japan have been lifted with forklifts and f**ked almost irrepairably.
    • Yes, but it's not dumb or dodgy. You can build a perfectly good boost controller from a pressure reg, a relief valve (looks same same as a reg if all from Norgren or SMC, for example) and a check valve. I ran one for years. Only superceded with  EBC because I could get one for cheaps and wanted finer control.   THis mod is certainly not a sketchy boost mod, provided the boost is kept below the "spin to death" threshold of the turbos.
×
×
  • Create New...