Jump to content
SAU Community

Recommended Posts

Small drive shaft that runs between both motors on electric chairs(is at the front of the chair)

Reclining Motor cover on passenger side chair

Rear LHD door armrest plastic screw cover

Passenger and driver air vents (large and small ones)

boot lid popper button

bolt to hold down spare wheel

Have a few more little bits and pieces but let me know if you have any of this stuff

  • 2 weeks later...
  • 2 weeks later...
  • 2 months later...
  • 3 months later...
  • 2 weeks later...
spose i should reply to this. sorry for the delay, but you ended up getting your parts hey?

Yeah I did

I still havent fitted them.

Had some issues with new bushes.

I will have to stick up photos as it was a massive problem making nolathane bushes fit on the lower control arms

  • 4 weeks later...

hey mate it has passenger front door missing drive line gone, all other panels, seats and trims, all cloth is badly sun damaged, it has no rear arms or diff or axles, would want about $600 but its pretty much usless unless you have a crashed cima..

give me a sms if you want 0450929227

Edited by E-Z
  • 3 months later...
  • 2 years later...
  • 1 month later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Shouldn't need a "base map" for anything other than guidance to ignition tuning. You just need the engine capacity right, the injector size right, and something, almost anything, for a VE map. On an NA engine, fuelling is almost completely a function of load signal & rpm. It should run and drive with a completely flat fuel map. It will be too lean under load, but that's easily fixed. We used to tune all ECUs without any base map. There were no such things (until someone had tuned a near stock engine on one, and then they had a "base map".
    • What did you actually buy/how much did it cost? When I got mine in like.. 2017...? 2019? the aim was to run Torque for gauges via ODB2 and things like Track Addict/Laptimers/Dashcam/Reversecam/Spotify etc. Mine never broke, but I wonder if you've got the same needs (it sounds like it). Cause I liked the idea of being able to do anything with it. That said, yours also cost 3x the cost of what I spent so... food for thought.  
    • For me there is a massive difference in manufacturer or big brand crippled android (Sony, Kenwood etc) vs the sort of thing I've installed here, which is basically just a tablet in DIN form factor with open Android, and the other model of course is mirroring - Android Auto/Carplay. I hate the locked down manufacturer and AA options where they decide what apps I'm allowed to install, including the Launcher but also importantly things like Ecutek (for this car) or Real Dash (Stagea) are not supported. Plus those crippled versions tend to be slower due to both overheads and lower spec hardware. On the other hand, when this breaks I'll likely be in trouble for support....but how is that different to owning an Infiniti anyway
    • Yeah, Duncan is helping sell me back to Android devices. I've hated the whole Android head units due to their speed issues. Even in my old Hyundai Kona (2022 model), it behind the scenes was Android, and slow and shitty to start up. Once running wasn't bad, but still a good 15 to 30 seconds.
    • My roof rails are off atm on the E39 until the rust is fixed. I did find another little bit of surface rust under the rails when I took them off. As @soviet_merlin said I'd just leave them alone unless you're planning on ensuring they're properly sealed. I was on the fence about leaving them off as the delete is still a thing in BMW E39's but I feel like the car is missing something (er, it is, der) with them off and I'm looking forward to putting them back on.
×
×
  • Create New...