Jump to content
SAU Community

Recommended Posts

Hi everyone,

just wondering if i could ask a favour from any R34 owners out there with FACTORY XENON headlights (NOT aftermarket H1 kits to deal with butchered compliance headlights).

I've never actually seen what the factory lights are like at night and was wondering if anyone would be so kind to take a pic of their car at night, facing a wall, garage door, etc... preferably not parked too close to the wall/door.

Basically i want to see what the cut-off and beam pattern is like, etc....

cheers!

daniel

Link to comment
https://www.sau.com.au/forums/topic/224946-a-little-help-from-r34-owners/
Share on other sites

  • 1 month later...

Mine were put back in after compliance and they are sweet i would never buy another car without them they are brilliant for night driving. Hope this is what you were after my camera sucks tho. The drivers side one points lower but they throw a huge beam and bright as f$#k you can barely look at roadsigns you drive past there that bright

Picture143.jpg

Picture144.jpg

Picture145.jpg

Edited by AndyD

what year is your stagea?? i'd also doubt they are projectors.... OEM Xenon projectors look like this...

gallery_1486_103_217836.jpg

i appreciate the post ;) but every reflector assembly has a different light patern, so i was kinda chasing someone with OEM R34 shots. Having said that though, we might have diagnose something with your car that needs to be checked...

The more i look at the front pic of yours, the more i think they're not Xenon. You should be above the cut-off line there with the angle you took the front shot, but you can still see a fair amount of glaring. This is a hallmark of an aftermarket HID kit in a reflector assembly not designed for it. A Xenon bulb (D2s, D2r, etc) has a certain light "signature" and the reflectors are designed to suit. You put in an H1 or whatever globe, the "pattern" of light doesn't match up and you get flaring everywhere, hot spots, etc.

The front shot does make the light look too yellow to be Xenon, could just be the pics

Is there a way to check like a part number or something. They look a little yellow cos of the parker globe which sits directly below the xenon,plus my camera sucks really bad and it was taken with the flash on. When looking at them they really are a purple/blue color,im not doubting what your saying but the camera really doesn't do justice to how it really looks if there is a way to check let me know and i'll check it out as it was listed on the auction sheet as xenon's so if they aren't i will be just a little bit pissed off. Oh and it is a 1999 series 2 stagea

well i just picked my car up from the panelshop thisarvo n the replacement headlight they put on is HID but the one they didnt replace is ye-olde compliance hack job so ill try n get some photos before i get a replacement light. dont own a camera so have ta try n get my mates one.

My r34 has xenons, will try to take a photo tonight...but there are like 4 modes you can adjust the xenon.

I havent really worked out what these modes actually do except they kinda differ in height a little.

PM me if i forget. lol

Edited by JI34GT
Is there a way to check like a part number or something. They look a little yellow cos of the parker globe which sits directly below the xenon,plus my camera sucks really bad and it was taken with the flash on. When looking at them they really are a purple/blue color,im not doubting what your saying but the camera really doesn't do justice to how it really looks if there is a way to check let me know and i'll check it out as it was listed on the auction sheet as xenon's so if they aren't i will be just a little bit pissed off. Oh and it is a 1999 series 2 stagea

Andy, they come from the factory with Xenons, same as virtually every R34, but because they're not auto-leveling and don't have a washer function, they don't meet ADRs and are removed during compliance.

The easiest way to tell is point the car near a wall and watch what they do when you turn them on - Xenons will light up a bit like a street light - take a few seconds to reach full brightness.

JI34GT - that knob is to adjust the height of the beam, nothing else.

Edited by Iron Chef

i have Xenons on my R34 and there excellent and give such a better light then standard. i can try and get a pic of mine today or tonight. but i would reconmend them. if ur thinking of getting a set.

But ill warn you now, a new set of R34 xenon headlights will cost min of $2500 or about $1200 for second hand set.

adam

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • And finally, the front lower mount. It was doubly weird. Firstly, the lower mount is held in with a bracket that has 3 bolts (it also acts as the steering lock stop), and then a nut on the shock lower mount itself. So, remove the 3x 14mm head bolts , then the 17mm nut that holds the shock in. From there, you can't actually remove the shock from the lower mount bolt (took me a while to work that out....) Sadly I don't have a pic of the other side, but the swaybar mounts to the same bolt that holds the shock in. You need to push that swaybar mount/bolt back so the shock can be pulled out past the lower control arm.  In this pic you can see the bolt partly pushed back, but it had to go further than that to release the shock. Once the shock is out, putting the new one in is "reverse of disassembly". Put the top of the shock through at least one hole and put a nut on loosely to hold it in place. Put the lower end in place and push the swaybar mount / shock bolt back in place, then loosely attach the other 2 top nuts. Bolt the bracket back in place with the 14mm head bolts and finally put the nut onto the lower bolt. Done....you have new suspension on your v37!
    • And now to the front.  No pics of the 3 nuts holding the front struts on, they are easy to spot. Undo 2 and leave the closest one on loosely. Underneath we have to deal with the wiring again, but this time its worse because the plug is behind the guard liner. You'll have to decide how much of the guard liner to remove, I undid the lower liner's top, inside and lower clips, but didn't pull it full off the guard. Same issue undoing the plug as at the rear, you need to firmly push the release clip from below while equally firmly gripping the plug body and pulling it out of  the socket. I used my fancy electrical disconnect pliers to get in there There is also one clip for the wiring, unlike at the rear I could not get behind it so just had to lever it up and out.....not in great condition to re-use in future.
    • Onto the rear lower shock mount. It's worth starting with a decent degrease to remove 10+ years of road grime, and perhaps also spray a penetrating oil on the shock lower nut. Don't forget to include the shock wiring and plug in the clean.... Deal with the wiring first; you need to release 2 clips where the wiring goes into the bracket (use long nose pliers behind the bracket to compress the clip so you can reuse it), and the rubber mount slides out, then release the plug.  I found it very hard to unplug, from underneath you can compress the tab with a screwdriver or similar, and gently but firmly pull the plug out of the socket (regular pliers may help but don't put too much pressure on the plastic. The lower mount is straightforward, 17mm nut and you can pull the shock out. As I wasn't putting a standard shock back in, I gave the car side wiring socket a generous gob of dialectric grease to keep crap out in the future. Putting the new shock in is straightforward, feed it into at least 1 of the bolt holes at the top and reach around to put a nut on it to hold it up. Then put on the other 2 top nuts loosely and put the shock onto the lower mounting bolt (you may need to lift the hub a little if the new shock is shorter). Tighten the lower nut and 3 upper nuts and you are done. In my case the BC Racing shocks came assembled for the fronts, but the rears needed to re-use the factory strut tops. For that you need spring compressors to take the pressure off the top nut (they are compressed enough when the spring can move between the top and bottom spring seats. Then a 17mm ring spanner to undo the nut while using an 8mm open spanner to stop the shaft turning (or, if you are really lucky you might get it off with a rattle gun).
    • You will now be able to lift the parcel shelf trim enough to get to the shock cover bolts; if you need to full remove the parcel shelf trim for some reason you also remove the escutcheons around the rear seat release and you will have to unplug the high stop light wiring from the boot. Next up is removal of the bracket; 6 nuts and a bolt Good news, you've finally got to the strut top! Remove the dust cover and the 3 shock mount nuts (perhaps leave 1 on lightly for now....) Same on the other side, but easier now you've done it all before
    • OK, so a bunch of trim needs to come off to get to the rear shock top mounts. Once the seat is out of the way, the plastic trim needs to come off. Remove 2 clips at the top then slide the trim towards the centre of the car to clear the lower clip Next you need to be able to lift the parcel shelf, which means you need to remove the mid dark trim around the door, and then the upper light trim above the parcel shelf. The mid trim has a clip in the middle to remove first, then lift the lowest trim off the top of the mid trim (unclips). At the top there is a hidden clip on the inner side to release first by pulling inwards, then the main clip releases by pulling the top towards the front of the car. The door seal comes off with the trim, just put them aside. The the lighter upper trim, this is easy to break to top clips so take it carefully. There is a hidden clip towards the bottom and another in the middle to release first by pulling inwards. Once they are out, there are 3 clips along the rear windscreen side of the panel that are hard to get under. This is what the rear of the panel looks like to assist:
×
×
  • Create New...