Jump to content
SAU Community

Recommended Posts

I will reprogram a 300ZX ECU for my RB25DET / Silvia, cause I can't find a R33 one(I live in Canada), and cause I can't reprogram R33.

So my question is, what are the stock timing map like?

I guess it will be very close to RB20DET , does it make sense?

I already got the RB20DET...but I would prefer to make sure that they are like RB25DET.

Also, does anybody as the firing order for RB25DET ? (I have to compare with a 300ZX engine..if there are not the same, I will switch injector and coil pack wiring.

There is an R33 Ecu for sell on ebay: http://cgi.ebay.com.au/ws/eBayISAPI.dll?Vi...&category=31250

Try getting 95 model as they have better fuel maps. I got 204 rwKw with stock 95 model ECU and stock turbo.

Lippo: Yes, it will probably go better with a 95 model ECU

S14Drift: The Daughterboards are not easily available and expensive. Badbiki doesn't have one, they are more complicated. You can get a new Hitachi H8-534 CPU from www.grid.co.jp and program it with new maps but it's like $300 windowed (reprogrammable) CPU and that's not all you need.

Originally posted by TomR33

You can get a new Hitachi H8-534 CPU from www.grid.co.jp and program it with new maps but it's like $300 windowed (reprogrammable) CPU and that's not all you need.

Sorry but I don't read japanese....

I have an eprom programmer, eprom eraser...and all that, I have been tuning SR20DET in Montreal(Canada) for almost a year now...

I can get a 300ZX ECU for less than 100 Aus...and then reprogram it... so paying 100$ for something I can't retune doesn't make sense to me.

Did the R32 RB20DET had the VTC too ? if so I can probably buy on of these (cause the have eprom on board) and tune that?

I would prefer a RB ECU for only one reason, they have 2 knock sensor input...and the 300 ZX only has 1....

S14Drift:Try this if you can't read Japanese, it will give you a rough English translation: http://babelfish.altavista.com/babelfish/u...ml%2F28_07.html

The Rb20DET don't have VCT. That is the biggest problem in adapting Rb20DET ECU to RB25DET engine. Some people have done it by adding an additional board with a specially programmed PIC microcontroller and a transistor to control VCT.

Would you be able get me one of those 300ZX ECUs for less than $100 AUD?

Originally posted by TomR33

Would you be able get me one of those 300ZX ECUs for less than $100 AUD?

The best place is Ebay.com

There is a lot of these ECU for sale (at least 3 to 5 per week), some went for 38 $ US, and the last one I missed went for 43$ US...

If people don't want to ship it to Australia, I could have it ship here in Canada, then ship it back to you :)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • There are several aftermarket options available, from not-too-painful moneyhttps://justjap.com/collections/driveshafts-bearings/products/d-max-reinforced-replacement-rear-driveshaft-set-fits-nissan-s13-s14-s15-r32-r33-r34-c35 and  https://justjap.com/products/crank-motorsport-billet-rear-axles-fits-nissan-skyline-r33-gts-t-r34-gt-t?srsltid=AfmBOorQk4xkGUa98kO7v2ePLUiNt-HRrM2AwWNw9mbSIVE1ujBVwY__, all the way up to The Driveshaft Shop https://driveshaftshop.com/skyline-cv-axles/
    • Yeah based on old XRC5964S specs, it looks to be roughly GTX3576R sized? But this 5964S compressor will flow 90lb airflow somewhat similar to the compressors in both the GTX3584RS or G35-1050.. I fully expected the 0.64 rear A/R to choke up top - seems way too small from typical convention - but these are seemingly beneficial over the prior 0.82 results.. Be interesting to see if he comments on the EFR question in that thread - he mentioned in a prior video that BW EFR's were the "cats pajamas 10 years ago", but by the sounds of things all his kits have been using Xona for quite a while now.
    • Yeah it’s still got the oem manual gearbox and clutch, only kinda mods are a blow off valve, coil overs, and a aftermarket intercooler. Also had it for about 2 months now with a lovely midnight purple paint on it.
    • Yeeeppp, been following a lot of the testing on the latest Xona stuff and there are some mental results.  He also went over 1000hp @ 4 hubs on his Mainline with a XRE6364S (63mm) which was also well into the 20psi range before 4000rpm on a 2.5. Crazy stuff. Fwiw the XRE5964S is basically the modern equivalent of their old HTA3582 - would drive nicely enough on an RB25 or 26, but proven capable of a huge amount of power if you want to spicy with rpm tho even at sane boost levels will make stout numbers 
    • The axels in my R33 seem tired, and have a bit of play in them. I cannot find any new of course, not interested in buying used, but I am looking to see if anyone can identify some cross compatible axles. In the states I have seen suggested for S chassis the J30 axles, however for the skyline (as best I can tell) the lengths are about an inch off (2.5cm) on both sides. R33 my measure L 22" R 24.5" GPT L 22.5" 24.25" J30 L 23.5" 25.5"  so shaft length is probably an inch wider. Not sure if someone has another still remanufactured option besides the J30. I figured worst case I can buy a pair tear them down and swap the center shaft. My other option was reaching out to GSP to see if they cannot piece together a set, since the axle stubs are still manufactured, I wouldn't think it be that hard to find a shaft or make a shaft work. 
×
×
  • Create New...