Jump to content
SAU Community

Recommended Posts

Ive just built a 25/30 and want to upgrade the turbo to something a bigger. Currently i have twin T3/T4s and am thinking about something like a GT42 or GT45 or T51r.

Does anyone run any of these turbos on a 25/30 or 26/30? I want to use this on the street but mostly drags.

What revs do they start making boost and when is full boost??

Im not really worried about a bit of lag as i will be running nos to help bring it on boost.

I will have a rev limit around 8000rpm

Link to comment
https://www.sau.com.au/forums/topic/225208-2530-turbo-options/
Share on other sites

I can sell you my T04z setup if you can find me a GT35 (GT35r, GT3540, etc) setup.

All the turbos he mentioned are much bigger than a T04Z, I suspect he is shooting for a different target to what your T04Z would.

Here is a dyno plot from an R34 GTR running a GT4202R on an RB30DET (cammed 26 head):

rb30760whpnq8.jpg

Thanks for that Lithium. It looks like the GT42 will go alright.

Has anone used a GT45 on a 3lt??

And the T51r has been done before. But they do sound awesome.

What are my options from a different brand of turbo. Turbonetics???

Thanks for that Lithium. It looks like the GT42 will go alright.

And the T51r has been done before. But they do sound awesome.

What are my options from a different brand of turbo. Turbonetics???

Yeah the GT4202R is on a full weight R34 GTR that has only done one run down the 1/4 which was far from clean and did a 9 "off the trailer" with an H-pattern box. It will go faster....

What do you mean by "sound awesome", the concept or the actual sound of them?? If you mean the whistle, GT40, GT42, GT45 etcs all have the same kind of sound due to the anti-surge compressor housings :) As alternatives I believe a Turbonetics T76 or GTK1000 are in the same territory, as with Trust T88. All the typical 1000hp beasts. There is a really rare IHI RX8 for sale in NZ at the moment, I believe 1200hp rated... could go for that and be one of very very few. Unfortunately you'll never get a straight out answer on what exactly to expect, as I for one know of no one aside from maybe Indy race cars which have used them.

Here is the R34 with the GT42R doing its run to get an idea of what kind of ride you could be in for:

GTK 1000 could be a go. Is anyone here using one of these??

lots of people in the us using them on 2js should be comparable to a rb30 results wise

though they are pretty new so there wont be thousands of them to look at

  • 2 weeks later...

Im using a t70 which is a garret replica, (couldnt afford the genuine item :) ) Its rated to 700hp, 40psi, externally gated and is of considerable size :D A friend of mine used one on his wrx (shudder) and was getting boost by 4000rpm. So hopefully il spool up around 3000rpm and listen to it whistle all the way up to redline :( When funding allows il upgrade to the t51r.

What other turbos are people running when using a big single???

What power range exactly do you mean?

Check out this site - possibly a bit out of date but has some listed:

http://t04r.com/turbos.php

These days there are neat things like the Garrett GT4088R and GT4094R, and in NZ there was or is a IHI RX8 which is an ~1100hp really flash thing.... they are basically used on indy cars.... that'd be interesting to see on a Skyline haha

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
    • It was picked up on the MOT/Inspection that the offside front wheel bearing had excessive play along with the ball joint. It made sense to do both sides so I sourced a pair of spare IS200 hubs to do the swap. Unfortunately I don't have any photos of the strip down but here's a quick run down. On the back of the hub is a large circular dust cover, using a flat head screw driver and a mallet I prised it off. Underneath will reveal a 32mm hub nut (impact gun recommended). With the hub nut removed the ABS ring can be removed (I ended up using a magnetic pick up tool to help). Next up is to remove the stub axle, this was a little trickier due to limited tools. I tried a 3 leg puller but the gap between the hub and stub axle wasn't enough for the legs to get in and under. Next option was a lump hammer and someone pulling the stub axle at the same time. After a few heavy hits it released. The lower bearing race had seized itself onto the stub axle, which was fine because I was replacing them anyway. With the upper bearing race removed and the grease cleaned off they looked like this The left one looked pristine inside but gave us the most trouble. The right one had some surface rust but came apart in a single hit, figure that out?! I got a local garage to press the new wheel bearings in, reassemble was the opposite and didn't take long at all. Removing the hub itself was simple. Starting with removing the brake caliper, 2x 14mm bolts for the caliper slider and 2x 19mm? for the carrier > hub bolts. I used a cable tie to secure the caliper to the upper arm so it was out of the way, there's a 10mm bolt securing the ABS sensor on. With the brake disc removed from the hub next are the three castle nuts for the upper and lower ball joints and track rod end. Two of these had their own R clip and one split pin. A few hits with the hammer and they're released (I left the castle nuts on by a couple of turns), the track rod ends gave me the most grief and I may have nipped the boots (oops). Fitting is the reversal and is very quick and easy to do. The lower ball joints are held onto the hub by 2x 17mm bolts. The castle nut did increase in socket size to 22mm from memory (this may vary from supplier) The two front tyres weren't in great condition, so I had those replaced with some budget tyres for the time being. I'll be replacing the wheels and tyres in the future, this was to get me on the road without the worry of the police hassling me.
    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
×
×
  • Create New...