Jump to content
SAU Community

Recommended Posts

As above, May i know what size of Star Torx that is needed to remove two of the bolts at the side of the steering wheel as the largest available in my country is only R40 and its still small. One more question, where is the bloody fuse for the horn. It will make the steering removal easier if the horn doesn't operate when you try to open the damn nut.

Edited by teng
Link to comment
https://www.sau.com.au/forums/topic/225349-1996-r33-series2-steering-removal/
Share on other sites

Its an R50, You may want to disconnect power to the car before removing the airbag as it may set it off..

http://paulr33.skylinesaustralia.com/

Left Column, top to bottom: Right Column, top to bottom

10A – Rear Wiper 10A – Shift lock

10A – Anti-stop 10A – A/T control

10A – Starter Indicator 10A – Air conditioner

10A – Room lamp 10A – Engine control

10A – Stop lamp 10A – Air bag

10A – Electrics 20A – Blower motor

10A – Engine Control 20A – Blower motor

10A – Hazard lamp 10A – Audio

15A – Fog lamp 15A – Cigarette lighter

10A – Turn signal 20A – Front wiper

10A – Meters 10A – Mirror de-fogger

10A – Electrics 20A – Rear de-fogger

Note that the engine bay fuse / relay box has a fuse key printed on the inside of the cover in english

I got a T50 with my Torx set from i can't remember where, it was like 10 bucks tho... T50 is hte biggest one i have. works with the steering wheel.

You can just unplug the horns at the front of the engine bay.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hello , im new here and i have A31 home build  RB25det neo stock eng / turbo  aem ems 2 blue connector  aem 3.5 map aem cas disk aem wideband connected to ecu  355 lph pump 550 nismo yellow injectors side feed aftermarket regulator  and won’t start with base aem tuner basic tune eventually flipped cas 180 degree so it triggers on correct stroke not in exhaust cycle  Now it won’t start Wideband reads 10 and 11 at lowest fuel setting  and will share calibrations soon for aem tuner i think something is wrong in aem tuner    please if you have any information, am very grateful         
    • Legend. I ended up finding the facebook account of the owner of the first car i sent but sadly he deactivated the account. I think you’re right in saying it’s some sort of well done custom job. Really appreciate your help anyways.
    • Totally equivalent. Stock often goes from the comp cover because that's where the actuator is also installed and the factory needs 2" of hose to make the connection - and it comes as a pre-assembled unit. They totally have a boost reference from somewhere between the turbo and the throttle(s). Oh, jeez. Just do it in M12 then. We don't actually care that much. I would expect any such AN converter fitting to rely on an o-ring or some other seal onto a flat surface under the flange of the hex**, because bolt threads are no intended to provide a pressure seal. unlike..... pipe threads. **which also requires a suitably flat and smooth surface on the turbo's boss to provide the seal.
    • I also used NP   That’s were it’s seems to be the best place to fit it? All schematic shows also that it’s should be referenced from the turbo housing. But idk, I do see high hp cars without any connection or anything to their turbos, so I really don’t know how they connect their things
    • I do have loctite 243 and 246 and a few more models. I could drill it now in place and make new threads for m12 and order an4 - m12 coupling and fit that to the turbo. Run a braided hose to the EBC which I could get a an4 to 1/8npt 
×
×
  • Create New...