Jump to content
SAU Community

Recommended Posts

when i park in a driveway above 25 -30 deg. angle nose first it has trouble starting

and when i park at a 45 deg. angle nose first (steep driveway) it wont even start.

it'll kick over but the engine wont catch

but when i let it roll onto the even road it starts straight away :)

i'm thinking it's the fuel pump..........................mabye?

Link to comment
https://www.sau.com.au/forums/topic/225544-angled-starting/
Share on other sites

I park my stagea on a hill (not that steep, like 10-15 degrees, and I can never have it below or near a quarter full as it will not start cos fuel doesnt reach pump.

So yeah, quite likely something quirky about the fuel pump setup from those whisky drinking Nissan factory techs.... Apparently they musnt have to park on hills in Japan.

Link to comment
https://www.sau.com.au/forums/topic/225544-angled-starting/#findComment-3972673
Share on other sites

I have a similar issue, but not identical: I have noticed that whenever I park the car nose down my (steep) driveway, it takes about 60-90 secs before the (Power FC equipped) car wil stabilise the idle, as opposed to the 20-30 secs it takes when the car is parked on the flat. It hasn't really been a huge issue, just annoying. Not sure if this helps, but it may point toward a general design flaw in the Stagea, rather than a specific troublesome component. For the record, I have replaced the fuel pump, lines, rail and injectors with new items in the process of modifying it, so I can pretty safely assume it's not an issue with the fuel system, as it runs faultlessly in any other way... Not sure if that sheds any light, but that's my 2 cents' worth.

Link to comment
https://www.sau.com.au/forums/topic/225544-angled-starting/#findComment-3973424
Share on other sites

never park a stagea on a passenger side angle with less than 1/4 tank( steep gutter etc), car no go :D

yep i had the same problem with mine, fuel pickup must be on drivers side so it cant get fuel when parked on passenger side angle. its happened to me many times as i have a steep driveway, ive learnt now to park my car face up. i Know its a pain in the butt. the only way round it would be to install a surge tank with extra fuel pump feeding it....

Link to comment
https://www.sau.com.au/forums/topic/225544-angled-starting/#findComment-3974466
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • My guesstimate, with no real numbers to back it up, is it won't effect it greatly at all.its not a huge change in position, and I can't see the air flow changing from in turbulence that much based on distance, and what's in front of it. Johnny and Brad may have some more numbers to share from experience though.
    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
    • Pull codes via the self-diagnosis procedure. As far as I can tell this is just a sign of transmission issues but not a code unto itself.
×
×
  • Create New...