Jump to content
SAU Community

Recommended Posts

Cheers Thomas,

Not a lot of room thats for sure.

Yep, just waiting for some valve shims and other stuff to come in from Japan ordered through nissan Blacktown.

Can't wait to get her on the road!!

Should be the longer drive on yours, get back to us on what you find. My engine was out of an R33 GTR by the engine number as it was changed before it came to Aus I'm sure.

I was going to go a fresh set of stock pistons, rings, bearings originally, or just the forged standard size pistons to freshen up till I found the scores.

Bore and hone cost $350 (sort of a favour) thats why I got away with keeping costs down, head skimed, cleaned etc $90. All the rest, done myself.

The hardest thing is not spending more money on crap you didn't put in your goal, budget. It really can snowball, gotta draw the line somewhere lol.

Edited by GTRsean
  • Replies 109
  • Created
  • Last Reply

Top Posters In This Topic

Cheers Thomas,

Not a lot of room thats for sure.

Yep, just waiting for some valve shims and other stuff to come in from Japan ordered through nissan Blacktown.

Can't wait to get her on the road!!

Should be the longer drive on yours, get back to us on what you find. My engine was out of an R33 GTR by the engine number as it was changed before it came to Aus I'm sure.

I was going to go a fresh set of stock pistons, rings, bearings originally, or just the forged standard size pistons to freshen up till I found the scores.

Bore and hone cost $350 (sort of a favour) thats why I got away with keeping costs down, head skimed, cleaned etc $90. All the rest, done myself.

The hardest thing is not spending more money on crap you didn't put in your goal, budget. It really can snowball, gotta draw the line somewhere lol.

Hey Sean..

Hopefully I find out about that drive sometime this week.

Definately know where your coming from about drawing the line.. Like I said same situation as you were in a few weeks ago.. Yet to open her and decide what needs to be done all pending on condition..

Cheers Tomek

coming along nicely! :P cant wait to start on mine..

as for the budget thing here's my story.. was going to put the n1 motor i bought straight in.. took 5 months to get here so i started buying bits and pieces.

then when the motor arrived i was told to pull it down to inspect, which moved me towards a full rebuild, lucky as there are some small scores up and down the bores on most cylinders, so a rebuild was a must.

hopefully will finish up under 10k haha

Cheers Andrew.

Wish I had an N1 block lol, nah, not for my application :(

Scores in the bores?, how deep are they?. It would be nice if they disappeared with a light hone would be nice, but I guess you will take it out to 86.5?

  • 3 weeks later...

Nearly there!

post-12712-1221734795_thumb.jpg

match ported manifolds while they were out.

post-12712-1221734837_thumb.jpg

post-12712-1221734885_thumb.jpg

New shims to do valve clearances.

post-12712-1221734921_thumb.jpg

post-12712-1221734957_thumb.jpg

post-12712-1221734990_thumb.jpg

post-12712-1221735043_thumb.jpg

Bolting up as much as I can before it goes back in.

Craved is nearly finished. Loving his work.

post-12712-1221735136_thumb.jpg

Nope. I'm happy with what I put in it. I'll kick myself hard later, but N1 pumps go ok.

Still have to find out what housing I have here, that I was going to put the billet gears in and use in the engine. It's not an N1 pump so I didn't use it due to being unsure of what I had. Still don't know, no one knows.

post-12712-1221741540_thumb.jpg

The one on the left. No idea?????

Have I lost anyone lol.

Tomoz morning is the plan.

The other thing I did the other day was setup and adjust the inline throttle setup. Completed that in accordance with the manual, and it's pretty easy after you read it like 5 times lol. Nice and smooth and all good.

There was a couple o little things this arvo to get done before she goes in, like fit the balancer and torque to 350,000 foot pounds lol. And fish out a washer I dropped down the front cover GRRRRRRRRR! It's out phew.

Got covers off Craved today :P:P .

The guys who spotted the covers in the shed were blown away lol, no complaints here lol.

post-12712-1221826523_thumb.jpg

Engine bays is a bit neater.

post-12712-1221826555_thumb.jpg

post-12712-1221826586_thumb.jpg

Just befor balancer was fitted.

Edited by GTRsean

Thanks Brad!

What a long day. Tired and got a headache.

Had to improvise with no chain for the engine crane this morning, (mate borrowed it a month ago).

Twin plate clutch was the first thing to go on this morning.

Cracked the s#%ts with crawling under the bloody thing later in the day. :D

Had a mate help me but had not much experience, so I'll be finishing up tomorrow.

To do tomorrow:

Bolt up gbox x member

Fit center tailshaft bearing mount

Fit a couple of belts and fan

CAS sensor

wiring

pipework

front suspension top nuts

gear shifter

Fill up oil, and do up sump plug!

Fill front diff.

Fill power steering

Coolant and bleed

Crank over, then start!

Bed in engine. ;)

post-12712-1221911306_thumb.jpg

post-12712-1221911340_thumb.jpg

post-12712-1221911365_thumb.jpg

post-12712-1221911390_thumb.jpg

post-12712-1221911433_thumb.jpg

post-12712-1221911463_thumb.jpg

post-12712-1221911496_thumb.jpg

post-12712-1221911524_thumb.jpg

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • The rain is the best time to push to the edge of the grip limit. Water lubrication reduces the consumption of rubber without reducing the fun. I take pleasure in driving around the outside of numpties in Audis, WRXs, BRZs, etc, because they get all worried in the wet. They warm up faster than the engine oil does.
    • When they're dead cold, and in the wet, they're not very fun. RE003 are alright, they do harden very quickly and turn into literally $50 Pace tyres.
    • Yeah, I thought that Reedy's video was quite good because he compared old and new (as in, well used and quite new) AD09s, with what is generally considered to be the fast Yokohama in this category (ie, sporty road/track tyres) and a tyre that people might be able to use to extend the comparo out into the space of more expensive European tyres, being the Cup 2. No-one would ever agree that the Cup 2 is a poor tyre - many would suggest that it is close to the very top of the category. And, for them all to come out so close to each other, and for the cheaper tyre in the test to do so well against the others, in some cases being even faster, shows that (good, non-linglong) tyres are reaching a plateau in terms of how good they can get, and they're all sitting on that same plateau. Anyway, on the AD08R, AD09, RS4 that I've had on the car in recent years, I've never had a problem in the cold and wet. SA gets down to 0-10°C in winter. Not so often, but it was only 4°C when I got in the car this morning. Once the tyres are warm (ie, after about 2km), you can start to lay into them. I've never aquaplaned or suffered serious off-corner understeer or anything like that in the wet, that I would not have expected to happen with a more normal tyre. I had some RE003s, and they were shit in the dry, shit in the wet, shit everywhere. I would rate the RS4 and AD0x as being more trustworthy in the wet, once the rubber is warm. Bridgestone should be ashamed of the RE003.
    • This is why I gave the disclaimer about how I drive in the wet which I feel is pretty important. I have heard people think RS4's are horrible in the rain, but I have this feeling they must be driving (or attempting to drive) anywhere close to the grip limit. I legitimately drive at the speed limit/below speed the limit 100% of the time in the rain. More than happy to just commute along at 50kmh behind a train of cars in 5th gear etc. I do agree with you with regards to the temp and the 'quality' of the tyre Dose. Most UHP tyres aren't even up to temperature on the road anyway, even when going mad initial D canyon carving. It would be interesting to see a not-up-to-temp UHP tyre compared against a mere... normal...HP tyre at these temperatures. I don't think you're (or me in this case) is actually picking up grip with an RS4/AD09 on the road relative to something like a RE003 because the RS4/AD09 is not up to temp and the RE003 is closer to it's optimal operating window.
    • Either the bearing has been installed backwards OR the gearbox input shaft bearing is loosey goosey.   When in doubt, just put in a Samsonas in.
×
×
  • Create New...