Jump to content
SAU Community

Recommended Posts

  • Replies 109
  • Created
  • Last Reply

Top Posters In This Topic

Ha ha. All done!!!! YAY!!!

Finished off all the little crappy stuff in the engine bay and under the car then at 4:30pm finally ran it on the starter to get oil flowing. Could hear every cylinder, nice.

Then started it for real, fired into life after 3 seconds : )

Drove to the servo and loaded it up on the way there and back, with the waste gates free so no boost to help bed in rings.

Came back, dropped the oil and put more mineral oil in and changed filter and hooked waste gate rods back up. Went for another drive, nice! Good to be driving her again.

Only problem may be that I need a new idle control valve :( as the engine revs (flares) by itself continuously at idle.

Sounds throatier than before too.

post-12712-1221993103_thumb.jpg

post-12712-1221993130_thumb.jpg

post-12712-1221993167_thumb.jpg

post-12712-1221993197_thumb.jpg

post-12712-1221993231_thumb.jpg

Cheers

Thanks :(. In the end I think I owe myself 5K+ lol. Great experience, and knowing the fact you built it yourself!

Well, on the stock bottom end it was putting out 350RWKW on 17psi. So I'd be happy with the same amount (read 500hp atw). Mainly due to he stock gearbox, and I built it to handle the power reliably without worrying about what the bottom end is like.

Went for a drive tonight, and it's really smooth and sounds gutsy lol. I'm only taking it to 4500 to 5000 at the moment at part throttle. Put 110k on it lol.

I'll book it in for a tune once it's got some kays under the belt........we'll see.

great work sean!

looks nice. and i love ur display pic. car looks smooooth as!

cant wait to see the dyno results. sounds promising!

Cheers. They really like taking your money lol.

Unplug it. Need to meet up for a cruz soon when i get my car back.

I'll try it out Brad. I also need to make another dummy load for the hicas solenoid I pulled out of the engine bay to stop the computer thinking theres a fault.

Cruise, for sure. I'll do the Putty cruise in October now :banana:.

Damn Sean, very nice and very fast work - fkn great effort!!

going to bug you for a ride in it soon if i get a night out i'll bring the SLR and take some shots!

Thanks Chris. The engine covers you did for me look awsome with the polished stuff so kudos to you. When we get a chance (read time off from busy schedule) for sure.

unreal sean. ive booked the gtr in for tune weekend after the long weekend at uni group. so will all have to go for cruise very soon. i just need front bumper now!!!!!!!!!!!

I'm glad it's done. Now done over 200k, and it's smooth as. Will be great when you get yours tuned.

I'd also like to thank everyone who gave some advice and imput on how to go about doing this project. 3 months seemed forever to me but it was pretty quick in the end.

post-12712-1222094499_thumb.jpg

Okay! Put 1200km on it so far, changed oil and filter again at 1000k and check up and tune on dyno is booked for tomorrow morning (only good thing about shift work lol). Gonna check a/f ratios etc, to make sure it's happy when I use the upper end of the rev range :P .

It has a pretty beaty, cammy idle, only using 12psi to be safe lol. I guess I'll have to check nuts and bolts are tight too etc. Twin plate clutch is great compared to the triple I had for the street.

Also the engine has no slap or rattles when started and warming up. Engine builder I took the block and pistons to, recommended running piston to bore clearance at 3.5thou so I'm happy.

Edited by GTRsean
Congratulation Sean..

Amazing how quick the build was done mate specially with work space..

Looking forward to updates.

Cheers :(

Okay, got it dynoed and cleaned up this morning. Found a couple of things. The fuel reg might need changing as it's a bit sus when revs are high at full load, more fuel was added to compensate but not too bad as it's on min 11 PSI boost anyway. Ordered in one from nissan. It idles at 1400RPM, idle control valve is letting too much air through(o ring inside is non existant), and I cleaned the throttles :D even though I read a topic about not to do that years ago!! It takes the sealing coating off the inside of the butterfly to bore seal.

Other than that, all good and since cam timing is sweet the gaph is great. It'll go back to the dyno in 2000km to get a high boost tune lol.

post-12712-1222827842_thumb.jpg

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Mixing things up - installed some leather recaros to match the leather seat covered rear seats. Interior looks pretty schmick now except for some slight wear on the steering wheel which I will monitor and address if it becomes worse or actually noticeable!  
    • Didnt realise RB's had more then 1 head.
    • I'm normally copping my own abuse from neglecting my daily drivers. "Those suspension bushes will last a bit more", "Don't worry about the oil leak, just keep topping it up". The project cars I'm always doing things slowly on them as I'm wanting them to be done better, and neater, and nicer. Luckily I don't have to deal with 18 year old Matt's "Learning to wire" stuff in the project cars. And there's only one piece of wiring I'm displeased about in the Landcruiser, and it's about to be cut out... However, the box loads of parts that have been going through this place lately for the Landcruiser... Brake pads Brake Rotors Full handbrake overhaul Wheel Bearings Seals Swivel hubs Steering Boxes Half the suspension joints Shocks Air bags (Ones to go in the rear springs for towing) Water pump Timing kit Lower timing case Harmonic Balancer Radiator Lots of other little seals and shits Gas struts for the bonnet New power window switches And god knows what else I've forgotten... Ha ha ha I have my fingers crossed the pinion seals don't start leaking on the diffs, that the transfer case doesn't leak, and the gearbox input shaft doesn't leak, nor the rear main seal. As they're about the only seals I haven't replaced in the driveline! I'm seriously eyeing off buying new caliper rebuild kits front and rear brake calipers... I'll probably recheck all the valve clearances soon too, and hopefully, it should be all good and sweet to haul some long distance trips again!
    • Every time I pull my 3x gauges out of the console and see the crack-addict way that I did the wiring, and I just can't bring myself to tear it all apart and "make it nice", because it is currently working. In fact, the last time I was in there I probably made it worse.
    • The best part is when you own the car long enough that you look back and find your OWN ham fisted amateur shit!
×
×
  • Create New...