Jump to content
SAU Community

Recommended Posts

I get PM's all the time asking for my price on Mickey Thompson ET Street Radials so I thought it'd be easier to just post them all here and if you need some you can let me know. These are the only ones in stock at the supplier right now so it's pointless putting up prices for the other sizes as they'll likely be different when they finally lob in Aus.

All prices are each.

MT3752R 235/60R-15 $292

MT3756R 255/60R-15 $291

MT3740R 205/40R-17 $255

MT3732R 215/60R-14 $206

MT3730R 205/50R-14 $228

MT3745R 295/45R-17 $342

MT3780R 245/40R-18 $342

MT3782R 265/40R-18 $370

MT3784R 315/30R-18 $457

MT3786R 305/45R-18 $403

Link to comment
https://www.sau.com.au/forums/topic/226442-mickey-thompson-drag-radials/
Share on other sites

Tell me about it!!! The 255/50/16's and 275/40/17's are the two most popular sizes with Skyline guys'n'girls. They're not receiving enough stock and it's all selling out straight away as backorders.

Put it this way; the Aussie distributor only got 44 of the 275/17's and they were all sold in two days. I reckon the manufacturer is holding out on them to be honest. The 18's still work bloody well. I've run just as quick to sixty-foot with the low profile versions as I have with the 50 series.

hmmm might have to try the 18's out...

I still have one set of 16's (new) but they are old skool street drags (came on the rims) ..... might as well use them seeing as there won't be anymore for a while... :sick:

  • 3 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • What copper washer do you guys use on the bleeder bolts? The existing one I have I had no idea where to find it in a local store, I did buy some online but that are only 1mm thick whereas my old one is 2mm+ thick and when I put the new washer out and squeeze the top radiator hose I can hear a bit of air but not with the old one. Does this matter? The new one doesn't leak, but the inner diameter is a bit loose whereas the old one threads on the bolt.
    • Howdy all, after being out a few weeks ago on a spirited drive in my GTR I have 2 issues that oddly have appeared at the same time. Whilst accelerating quickly through the gears all of a sudden i’ve lost power at the top of third gear (below redline around 6000rpm) for no obvious reason.    From that point onwards the car has been running rich on idle, won’t really rev under load without a ton of black smoke and the odd backfire, and dying as a pull up to a set of lights unless I keep the revs up around 1500rpm. In addition when shutting down the car that same night (I was 10 minutes from home) I noticed one of the turbos was significantly noisy on wind down when shutting off the engine. After letting the car cool down overnight it starts up fine, although once it gets to temp the revs start to creep up and down, the exhaust is darker than it should be and it also sounds like it’s running rich (fat note) I’ve put a new set of plugs in it - no change, the old plugs all seemed OK with two of them being somewhat richer/fueled up than the other 3 with 1 being borderline. I’ve smoked tested the intake system via the front of the Turbos, found a split vacuum hose going to the factory boost gauge sender, which I have since replaced.  Also found another leak on the gasket coming off the rear turbo outlet, have also replaced this. After fixing both of these leaks - still have the running rich issue. I’ve also tried another pair of AFM’s - no change here After pulling off the front turbo intake pipes, there is obvious shaft play in the front turbo, which now hisses loudly on light revvs although I can’t see why this would make the car run funny even under idle. I’m curious to know why it’s running rich before I potentially replace/rebuild turbos. The car is completely stock <50,000kms  other than an exhaust. Oil and coolant are all clear. I haven’t bothered with coil packs as it looks like they won’t be the issue due to condition of the plugs. Any help appreciated as I cry myself to sleep!
    • No probs at all. I used to love trying to dig up obscure info for those in need where possible going back 20+ years on SAU.  I did have another look and couldn't come up with any closer match. I'm leaning towards those skirts in your first pic are custom fitments, cut down/extended or from another car entirely and modded to fit an R34 sedan. I would've thought someone in Japan had them and taken a photo at some stage over the last 2 decades but there's nothing. Someone out there must know surely.
    • Welcome mate. Any pics? Even with a DE I'd be well happy if I had that as a 1st car. 
×
×
  • Create New...