Jump to content
SAU Community

Recommended Posts

Just a question to save me some stuffing about.

I have an airleak like sound once the engine trys to come on boost and power flattens off along with boost not really holding.

Other than that the engine idles great and runs very nicely under load upto the point where you try to get some boost happening.

It all started after I was demonstrating the NOS system to Miko the other night and blew off an intercooler hose, as always you crap yourself when that happens :). Due to lateness of the hour MIko and I took 4 times as long as a single non-tired person would to fix the hose.

Anyway I specualte the BOV and hope it isn't a turbo gasket or something.

Input apreciated.

Link to comment
https://www.sau.com.au/forums/topic/22682-blow-off-valve-leaking-or-what/
Share on other sites

Rev - I thought the standard BOV was good for 1000hp at 10 Bar? :)

Seriously - sounds like the BOV. I've got a stock one sitting round that you can bolt on to test if you like. Drop me a PM and I can give it to you over the weekend.

hey i have go fast bits mach 1 trumpet bov and i reckon its pretty good (its red) hehe hehe well anyway ive got no leaks or nothing they reckon the gfb bov are one of the strongest and have a special seal and they dont leak.. i got mates with hks and one like that and he has leaking trouble to.. well ive had 2 gfb bov and no trouble yet so im happy with them and gonna stick with them.. happy bov customer.. talk to tecknik audio they did the coolest job.. ohh sorry are you allowed to plug perfomance shops .. ahh well.. old skool cuz

The BOV I suspect because the leak occurs under boost only and has not got any worse. It could be a small split in a hose that opens up under boost too, but I think the BOV might be the first port of call (easiest to check).

I think I missed the cruise this morning, I was up till 3am last nite working out the family finances for a tax evaluation :(

It was leaking around a plug that was installed to block a pipe.. only very minor though. Not sure if it would've cause the problems that Rev was describing..

You're a curious little cat this morning aren't ya? :)

Cam,

it appears that it is probably the little vacume hose we found. Even after we blocked it up as soon as I took off it was doing the same thing again. Normally when I take off quick I get a decent amount of wheel spin, unlike last night.

I'll probably do a propper job of blocking the hose off today and see what happens.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...