Jump to content
SAU Community

Recommended Posts

as per subject, with continental contisport 225/45 and 245/40 rubber with about 50% tread

good condition. few small scratches and small kerb rash on one wheel.

great jap wheels with a nice big polished deep dish. Lighter than stock 200sx/skyline wheels!

5 x 114.3, offset is 38 and 45 i think? im not too sure on that, the offset sticker has peeled off the fronts, but the back is 45 im pretty sure. off s15, but will fits s14, r33 etc

selling because im a riceboy at heart and need some bigger wheels :)

$1700 ono.

in sydney, email [email protected] for more info and more detailed pics.

car.jpg

wheel.jpg

wheel2.jpg

wheel3.jpg

wheel5.jpg

wheel6.jpg

wheel7.jpg

no sorry jay but i do take mastercard and diners hahaha :(

sikcar: i have pics of the scratches, give me your email and i'll send them to you. as for shipping, i've got no idea how much it would cost, ill try and find out tomorrow

a few ppl are going to have a look at them today and tomorrow, we'll see how that goes otherwise ill look into the freight side of things.

id really rather just hand them over in person :D

i did it myself.

2 dollar spray can from bunnings.

i did it about 4 months ago and thats how it looks now, the photos were only taken a few days ago.

f-k heat resistant paint, waste of money.

  • 3 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Have you done the Ignition Sync Wizard in the AEM software?
    • Find out what RPM it was idling at with the IACV unplugged. It's very weird that the rpm didn't change at all, and then it stalled. When it stalls is it nearly like a switch off, like you've turned the engine off? Or is it more stutters and sputters and coughs to death over a few seconds? Or does the RPM just slowly keep going down and down? Have you done a test of trying to start it with the AFM unplugged? Does it still die?     If you Follow Josh's advice on using Nistune to check the voltages (which is a perfect method!) if you see anything out of wack voltage wise, THEN get the multimeter out and read the voltage directly at the sensor. If the two vary, then you're now looking for a wiring issue vs a sensor issue. So be aware, what the ECU sees, may not be what the sensor is actually saying too...
    • You very likely need to get it on a dyno and tune it. My assumption is, you've got an RB25DET tune in it, which has a different manifold, different injectors, and different cams as a minimum. What O2 sensor are you running?   When you say it runs extremely rich from idle all the way to redline, is this just free revving it you see that?
    • I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
    • I don't know any details, but I really wouldn't be surprised if they do it as a LHD only version, at least initially.
×
×
  • Create New...