Jump to content
SAU Community

I Hate People

Helio

By Helio,
in Victoria

 Share

Recommended Posts

Helio Proficient

Helio

Posted
Posted

Thought That I might have a rant. :)

Was driving to work this morning when some a-hol was traveling to close to the center of the road and demolished my drivers side mirror. It was a fairly narrow road but safe enough for two cars to pass with out incident, or so I thought. The prick didn't stop, or even slow down. I turned around and caught up and got his rego, then reported it to my local police station. Won't go well with insurance though, if he doesn't admit to it, my word against his and no witnesses. F*#$&& pissed off. Any one have an idea on what a replacement mirror for a GTST 33 series 2 is? :D

Link to comment
https://www.sau.com.au/forums/topic/227671-i-hate-people/
Share on other sites
WYTSKY Veteran

WYTSKY

Posted
Posted

bad luck mate.. some people just don't care and have no concience.... on the somewhat positive side Im sure youve seen how many wrecked cars are on here.. Im sure you'll find a good new mirror cheaply enough..

try to be an optimist instead of a pesimist.. (i don't know how to spell)

eg... he did get your mirror, but thank god he didn't touch any other part of your car.. imagine the cost of replacing a door and repairing front and rear quaters?

best of luck,

Adam

Link to comment
https://www.sau.com.au/forums/topic/227671-i-hate-people/#findComment-4007481
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Duncan
      S1 rb25/s14 starting problem

      By Duncan · Posted

      Depending on how long the car sat it is very possible for injectors to be stuck open or closed, I'd get them cleaned and flow tested. Other than that, obviously when the loom changes and the car doesn't start any more....the loom is suspect so some tracing / comparing may be required
    • 25zenki
      S1 rb25/s14 starting problem

      By 25zenki · Posted

      Harness is for a s1 Rb25det, and it is engine and lower harness.  the old harness had broken off plugs and was in very rough condition/exposed wires and splices etc. it is not able to be put back on the car, I could visually inspect to see if they had rewired any pins on the ecu plug. The fuel pump definitly isn’t turning off it’s an external pump and very loud you can hear it. Will look at the other harness tonight, am also going to pull the fuel rail and watch the injectors spray, will update here with what I find. Pretty sure at this point it has to be something to do with injectors because car will fire up on starting fluid and cas is clicking the Injectors. Fuel pressure is steady 43psi 
    • Waders360
      M35 Brake caliper replacement

      By Waders360 · Posted

      Sorry. Front brake calipers
    • MBS206
      S1 rb25/s14 starting problem

      By MBS206 · Posted

      Check the injectors flow evenly, and are actually flowing what you and the ECU think they should be flowing. If it's starting up on starter fluid, you have a fuel issue. Is it possible under cranking your fuel pump is turning off?   The harness you replaced, is that the whole engine harness? Do yourself a test, and drop the old harness on and plug it into the Z32 ECU. It's possible they've wired things different. From memory S1 to S2 is different in RB25 and you may have a wrong loom
    • 25zenki
      S1 rb25/s14 starting problem

      By 25zenki · Posted

      I haven’t pulled the injectors to watch them spray yet but they are clicking from the cas and all of the spark plugs are wet with fuel. I’ve thought the cylinders were being flooded from the beginning and was hoping fuel pressure would fix it. Tonight I am going to pull the rail and watch the injectors spray. Don’t know how to test/diagnose if the plugs are firing in correct sequence but that should be a timing thing and as far as timing goes my car still has the half moon for the cas can only install it 1 way. And my mechanical timing is 100% correct I posted photos above. Confirmed with the balancer on and off. 
×
×
  • Create New...