Jump to content
SAU Community

Recommended Posts

  • 3 weeks later...
  • Replies 91
  • Created
  • Last Reply

Top Posters In This Topic

production has already started . Hopefully a couple of weeks away.

Sweet, thanks mate, could you give me a heads up when they arrive???

ta!

well vi-pec was installed on monday just base tune map as dyno was busy .

car was dyno'd on tuesday and it makes similar power to the mines ecu i had in it

am extremely happy with the autoworx sales and service and am wrapped with lumpys tune

it still needs a bit more of a tune once i have found a stock 32 r boost solenoid as the bleed vleve in mine boost drops from 15 psi @ lower revs down to about 11 psi @ peak

YAYYYYYYYYYYYY no more AFM's to worry about

If you can't find the solenoid let me know. I have one at home you can have.

You've got an Rb20 solenoid??

Mark... its not the RB20 solenoid you're after, its the RB20 wastegate actuator :banana:

Edited by NISZILA
  • 1 month later...

woot woot :D

might call in early next week and pick one up

would you have the stock na rb25 neo map for it? I might plug it in before i do the conversion to see what the old na can pump out haha

finally got tune for boost and launch control done

dyno sheet

img013.jpg

it boost was deliberately tapered off at the top end to stop the turbos over spinning and killing their frail 14 year old ceramic insides

very impressive result given its a basically stock 32gtr!

have you had a chance to try launch control?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I get that taking off the head is best but that's a bit much for "just" valve seals. I was just under the impression that one would be able to rotate to TDC and be able to temporarily drop the valve without losing it and effectively having to remove the head to then recover it. I never knew people actually pushed rope into the cylinder to do valve seals hahaha So just to confirm, just going to TDC will not work? In that case I know when I do valve seals I'll maybe just remove the head and do some other things while I'm there, or just wait until I do an engine build.
    • The old approach was to fill the cylinder/chamber with a length of rope pushed in through the sparkplug hole. The new approach is to connect compressed air to the sparkplug hole and fill it with enough pressure to push the valves up. Doing either of these things with the head on and the engine in the car is a lot less pleasant than doing it properly.
    • Can't you put the pistons to TDC and then do the valve seals? Or will the drop down too far to pull them back up?
    • One thing I can tell you is, do it properly the first time. If you encounter unexpected problems just let the car sit for a week or two if you have to get some other parts or figure stuff out.  I'd have said go and use as many OEM parts as possible but since you want to change the turbo later on a custom kit is probably the better choice. Since I have no experience with RB25 just compare parts diagrams and images before buying a line kit and it should be easy to see if it has everything you need. Amayama has very good parts diagrams and part number lists, that is what I used a bunch to figure out what I might need. And don't forget to plan ahead and possibly renew other stuff that's easy to get to while you're in there doing the turbo lines. Happy wrenching
    • Update 4:   Hi all, good news. Engine is running and all the gaskets and seals seem to be working as intended. No leaks so far, even the JB Weld seems to hold. I flushed out the old coolant a few times and put in fresh coolant, not Nissan stuff, I decided to try the Ravenol Protect FL22, they claim it works for a wide variety of JDM cars and the opinions on it by some people were pretty good. And it has the nice poison green color! And man am I glad I bought a coolant system tester earlier this year, vacuum filling works wonders on this engine. I can definitely recommend this to anyone still doing it the old school way. All you need is compressed air supply. Will have to do a small test drive as soon as I can, I removed the gauge cluster again as the tacho needle was still bouncing around a bit but it was much better than before already.  I also found some cracks on all 4 tires inner and outer sidewalls. Apparently these tires should 't be parked on for extended periods or be kept under 0 degrees during storage, which I did not know. Clearly the previous owner didn't look into those details either, he probably bought them just cause they are cool semi-slicks. I'm just wondering how tf I am supposed to reach 30-80 degree tire temperatures on the public road consistenly, these tires were never going to work for my use case. I'll probably order Continental SportContact7 ones as these are the best allround summer tire available right now and I don't think I'll need anything crazier for now. Do let me know if you have experience with various tires and which ones you recommend.
×
×
  • Create New...