Jump to content
SAU Community

Recommended Posts

in the morning when i turn my car on..(infact anywhere where the car has been sitting for more then 30 mins off) theres a ticking comming from my bay, but only at around 2500>3000, not when its idleing, i pop the hood to find its comming from the front of the block, on the right side (turbo side) of the rocket cover when i rev it.. after driving for about 10 mins it goes away, what the hell is this..is it serious? thanks for reading :) car: R32 GTST 1992

Link to comment
https://www.sau.com.au/forums/topic/228428-weird-stupid-noise-heeeeeelp/
Share on other sites

Skylines and engine bay noises, do search...

When were your timing belt idler and tensioner pulley's last replaced? I've had this issue, I reckon i was a few weeks away from a seized bearing, overheated and snapped timing belt :)

Sure its not your injectors? If you race the motor, does the noise disappear on the decel? What oil and when was it changed last?

Regardless, poke about the engine bay with a long screwdriver on your ear.

i change oil every 3000k's, it started actually after switching from valvoline to caltex synthetic oil....timing belt changed at 93 000ks, its done 132 000 now..

lol sorry i tryed search b ut came up with similer issues but not the same, it ticks only wen i accelerate,, then it goes away completely... its perfect at idle..

Edited by SXCR32

Check your starter. There is a thing called "the clicker" it is known as this because, well, it clicks. When you start the car it should click for about... oh, I would say 10 minutes max when running. Normally it is out of 2nd gear as well because the engine is warmer. Then the clicking is better on warm days etc. That could mean a bad starter. That is why they make it like that. X__X;;

Happend to me and I ignored it, then I got stuck in the middle of nowhere.

Just something to ponder mate.

If this IS the case, don't replace it. It can be repaired for like 25$ easy. Take it to a shop is all.

Edited by AKW

since it was after a oil change i would also have to go with a lifter. get this a bit at work. when you change the oil and put a new filter on you induce a fair bit of air into your engines oil gallerys which can enter a lifter pretty easily, usually it will go away after a bit of driving. if not, lifter could possibly be on its way out...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Depending on how long the car sat it is very possible for injectors to be stuck open or closed, I'd get them cleaned and flow tested. Other than that, obviously when the loom changes and the car doesn't start any more....the loom is suspect so some tracing / comparing may be required
    • Harness is for a s1 Rb25det, and it is engine and lower harness.  the old harness had broken off plugs and was in very rough condition/exposed wires and splices etc. it is not able to be put back on the car, I could visually inspect to see if they had rewired any pins on the ecu plug. The fuel pump definitly isn’t turning off it’s an external pump and very loud you can hear it. Will look at the other harness tonight, am also going to pull the fuel rail and watch the injectors spray, will update here with what I find. Pretty sure at this point it has to be something to do with injectors because car will fire up on starting fluid and cas is clicking the Injectors. Fuel pressure is steady 43psi 
    • Check the injectors flow evenly, and are actually flowing what you and the ECU think they should be flowing. If it's starting up on starter fluid, you have a fuel issue. Is it possible under cranking your fuel pump is turning off?   The harness you replaced, is that the whole engine harness? Do yourself a test, and drop the old harness on and plug it into the Z32 ECU. It's possible they've wired things different. From memory S1 to S2 is different in RB25 and you may have a wrong loom
    • I haven’t pulled the injectors to watch them spray yet but they are clicking from the cas and all of the spark plugs are wet with fuel. I’ve thought the cylinders were being flooded from the beginning and was hoping fuel pressure would fix it. Tonight I am going to pull the rail and watch the injectors spray. Don’t know how to test/diagnose if the plugs are firing in correct sequence but that should be a timing thing and as far as timing goes my car still has the half moon for the cas can only install it 1 way. And my mechanical timing is 100% correct I posted photos above. Confirmed with the balancer on and off. 
×
×
  • Create New...